Bedienungsanleitung Fein FMM 250 (Seite 13 von 107) (Deutsch, Holländisch, Dänisch, Italienisch, Portugiesisch, Polnisch, Schwedisch, Norwegisch)

78185

Zoom out

Zoom in

Vorherige Seite

1/107

Nächste Seite

Handling hazardous dusts

For work procedures with this power tool where mate-

rial is removed, dusts develop that can be hazardous to

one’s health.

Contact with or inhaling some dust types, e. g. asbestos

and asbestos-containing materials, lead-containing coat-

ings, metal, some wood types, minerals, silicate particles

from materials containing stone, paint solvents, wood

preservatives, and antifouling paints for vessels, can trig-

ger allergic reactions to the operator or bystanders and/

or lead to respiratory infections, cancer, birth defects or

other reproductive harm. The risk from inhaling dusts

depends on the exposition. Use dust extraction matched

appropriately for the developing dust, as well as personal

protective equipment and provide for good ventilation of

the workplace. Leave the processing of asbestos-contain-

ing materials to specialists.

Wood and light-metal dust, hot mixtures of sanding dust

and chemical materials can self-ignite under unfavourable

conditions or cause an explosion. Avoid sparking in the

direction of the dust collector as well as overheating of

the power tool and the materials being sanded, empty

the dust collector/container in time, observe the material

manufacturer’s working instructions, as well as the rele-

vant regulations in your country for the materials being

worked.

At a glance.

The following numbering of the product fea-

tures refers to the illustrations at the beginning

of this Instruction Manual.

1 Quick-clamping lever

For clamping the tool.

2 Switch

For switching the power tool ON and OFF.

3 Thumbwheel for pre-selection of oscillating frequency

For pre-selection of oscillating frequency.

1=lowest oscillation rate.

6=highest oscillation rate.

4 Depth stop

For depth-of-cut adjustment .

5 Suction device

For dust-free operation, connect to a vacuum

cleaner .

6 Changing accessories, MultiMaster FMM250Q

Mount accessories with fastening element (6a).

7 Changing accessories, MultiMaster FMM250

Mount accessories with clamping screw (7b).

8 Tool holder

When mounting accessories, ensure positive lock-

ing.

9 Sanding sheet

Attach sanding sheet with Velcro backing.

10 Vibration-damping FEIN gel work gloves

Reduces the vibrational stress.

11 Standard accessories

Allen key (11c).

Operation of the power tool off power generators.

This machine is also intended to be powered by

a.c. generators with sufficient power output that

correspond with ISO 8528, design class G2. Com-

pliance with this Standard in particular is not given when

the so-called distortion factor exceeds 10%. When in

doubt, inform yourself about the generator in use.

Instructions for putting into operation.

Mounting the suction device (Figure 12).

➤ Mount the suction device step by step as shown

in the figures.

For connection with a FEIN Dustex or a vacuum cleaner,

various hose adapters are available as an accessory.

➤ To remove the suction device again, push the

clamp at the mark to the rear. (Figure 12-8)

Operating instructions.

Changing the tool.

Do not use accessories not specifically intended and recom-

mended for this power tool by FEIN. The use of non-original

FEIN accessories can lead to overheating of the power

tool and destroy it.

For adjustment of the most convenient working

position, the application tool can be mounted in

45° steps.

MULTIMASTER FMM250Q (FIGURE 6).

➤ Loosen the quick-clamping lever (1) and swivel

it to the stop.

➤ Pull out the fastening element (6a).

➤ Clean the tool holder (8), the application tool

and the fastening element (6a).

➤ Place the application tool exactly onto the star-

shaped tool holder (8). Pay attention that the appli-

cation tool has a flush fit.

➤ Insert the fastening element (6a) to the stop into

the tool holder.

➤ Swivel the quick-clamping lever (1) back until it

engages.

Protect your hand and fingers against bruising them

when locking the clamping lever. The clamping lever

snaps back vigorously by means of spring force.

ULTIMASTER FMM250 (Figure 7).

➤ Unscrew the clamping screw (7b).

➤ Clean the tool holder (8), the application tool

and the clamping screw (7b).

➤ Place the application tool exactly onto the star-

shaped tool holder (8). Pay attention that the appli-

cation tool has a flush fit.

➤ Tighten the clamping screw (7b) using the sup-

plied Allen key (11c).

Attaching/replacing the sanding sheet (Figure 9).

➤ Align the sanding sheet and press it onto the

sanding plate by hand.

➤ Firmly push the power tool via the sanding sheet

onto a flat surface and briefly switch the power

tool on. This provides for good adhesion of the

sanding sheet and prevents premature wear.

3 41 01 078 06 0.book Seite 13 Dienstag, 16. März 2010 7:39 07

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fein FMM 250 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Fein FMM 250

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info