Bedienungsanleitung Fein FMM 250 (Seite 14 von 107) (Deutsch, Holländisch, Dänisch, Italienisch, Portugiesisch, Polnisch, Schwedisch, Norwegisch)

78185

Zoom out

Zoom in

Vorherige Seite

1/107

Nächste Seite

The sanding sheet can be pulled off again and then

remounted offset by 120° when only one tip of the sand-

ing sheet is worn.

Securing the work piece.

➤ Secure the workpiece firmly. A work piece that is

gripped tightly in a clamping device or vice, is more

secure than if held by hand.

General operating instructions.

Switching ON and OFF.

First check that the mains supply lead and mains

plug are not damaged.

Switching ON:

➤ Push the switch (2) towards the front (I).

Switching OFF:

➤ Push the switch (2) toward the rear ( ).

Presetting the oscillating frequency (Figure 3).

The oscillating frequency can be pre-selected infinitely

variable.

Increasing the oscillating frequency:

➤ Turn thumbwheel (3) in anticlockwise direction.

Decreasing the oscillating frequency:

➤ Turn thumbwheel (3) in clockwise direction.

The oscillating frequency depends on the application and

the application tool. Example:

– High oscillating frequency:

Sanding, sawing, using as a rasp, polishing stone and

metal.

– Low oscillating frequency:

Polishing of varnish and veneers.

Working instructions.

Sanding

Typical application: Dry sanding of wood and metal,

especially of smaller surfaces, corners and edges, as well

as hard to reach locations.

Work with the complete surface of the sanding plate, not

only with the tip. Select a high oscillating frequency. Sand

with continuous motion and light pressure. Applying

excessive pressure does not increase material removal;

only the sanding sheet wears more quickly.

Sawing

Typical application: Sawing of thin steel sheet, wood and

plastic components.

Select a high oscillating frequency. Round saw blades can

be loosened and attached offset, in order to provide for

uniform wear.

Scraping

Typical application: Scraping off old coats of varnish or

adhesives, removing bonded carpeting, e. g., on stairs/

steps or other small/medium-sized surfaces.

Select a medium to high oscillating frequency.

For further information as well as tips on polishing, cut-

ting, separating and using as a rasp, see the booklet “Ideas

for Usage”.

Storage (M

ULTIMASTER FMM250Q).

➤ Fully insert the fastening element (6a) into the

tool holder in order to protect it against damage

and contamination.

➤ Engage the quick-clamping lever.

Repair and customer service.

When working metal under extreme operat-

ing conditions, it is possible for conductive

dust to settle in the interior of the power

tool. The total insulation of the power tool can be

impaired. Blow out the interior of the power tool via the

ventilation slots frequently with dry and oil-free com-

pressed air, and connect a residual current device (RCD)

on the line side.

If the supply cord of this power tool is damaged it must

be replaced by a specially prepared cord available

through the FEIN customer service centre.

If required, you can change the following parts yourself:

– Application tools

– Fastening element (6a)

– Clamping screw (7b)

Warranty and liability.

The warranty for the product is valid in accordance with

the legal regulations in the country where it is marketed.

In addition, FEIN also provides a guarantee in accordance

with the FEIN manufacturer’s warranty declaration.

The delivery scope of your power tool may include only

a part of the accessories described or shown in this

instruction manual.

Declaration of conformity.

FEIN declares itself solely responsible for this product

conforming with the relevant provisions given on the last

page of this Instruction Manual.

3 41 01 078 06 0.book Seite 14 Dienstag, 16. März 2010 7:39 07

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fein FMM 250 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Fein FMM 250

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info