Bedienungsanleitung Ferm ATM1042 (Seite 6 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Norwegisch, Finnisch)

763846

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

A contaminated and blocked filter will cause a

reduction in the pressure, which will negatively

influence the performance of the air stapler.



When in use, always wear eye protection

that meets the ANSI specifications, and

offers protection both in front and at the

sides from flying objects when loading,

operating and maintaining the air stapler.

Flying fasteners and splinters can cause

severe injury.

The employer or user must insist that proper eye

protection is worn. Eye protection equipment

should meet the specification of the American

National Standards Institute, ANSI Z87.1-1979

and must offer protection from both the front and

the sides.

Glasses without side shield and face

protector do not offer sufficient protection.



Fig.5

• Disconnect the air hose.

• Release the fastener latch and withdraw this

along the fastener guide unit.

• Insert 1 fastener strip into the magazine.

Load with fastener points upwards.

• Press the fastener guide unit back into the

magazine, and lock the fastener latch.

• Reconnect the air hose to the air stapler.



When in use, always wear eye protection

that meets the ANSI specifications, and

offers protection both in front and at the

sides from flying objects when loading,

operating and maintaining the air stapler.

Flying fasteners and splinters can cause

severe injury.



• Read the general safety instructions and

warnings in these instructions for use

carefully.

• Refer to the specifications earlier in these

instructions for the correct operating

conditions for the air stapler.

Make sure the stapler is lubricated

properly before using it the first time.



Fig.1 - 4

A piston powered by compressed air drives the air

stapler. Illustrations 1 – 4 on page 2 + 3 show how

the air stapler works.





Pressing the trigger activates the air stapler. Every

time the trigger is pressed, the air stapler will drive

a fastener into the workpiece.

Keep your hands well clear of the fastener

head. On no account should you point the

air stapler at any person or animal.







Fig. 6

At the front of the tacker there is a cover with a red

lever.

This cover can be removed when a staple is

blocked into the shaft.

Warning! To avoid injury:

Disconnect the air hose.

First release the fastener latch and

withdraw this along the fastener guide

unit. Removing the cover, while the

system is under pressure, can cause

serious injury: the staples can jump out

of the tacker unit!



• Remove the staples from the guide unit.

• Pull the red lever of the cover (in front of

tacker) downwards and remove the cover.

• The blocked stapler can be removed.

• After mounting the cover, staples and fastener

latch can be placed again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm ATM1042 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info