Bedienungsanleitung Ferm ATM1042 (Seite 7 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Norwegisch, Finnisch)

763846

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite



Remove all fasteners from the air

stapler before you perform a check.

• Hold the tool firmly by the handgrip, without

your finger on the trigger.

• Set the fastener head of the tool against the

work surface.

• Press the trigger so that the hammer pin

emerges. Release the trigger and the cycle is

complete.

Every time the trigger is pressed, the air

stapler will make a complete cycle.



Whenever performing maintenance on

the air stapler, pay attention to the

warnings given in these instructions for

use, and be extra cautious when

troubleshooting problems with the air

stapler.



Original parts are recommended when

replacement of parts is necessary. Do not use any

alternative parts that cannot perform as well as

the original parts in the appliance.





Whenever you are repairing the air stapler, take

care to clean and lubricate the internal parts. Use

Parker “O-Lube” or similar on all O-rings. Coat all

O-rings with O-Lube before reassembling. Apply

oil lightly to all moving surfaces and pins. Finally,

following complete assembly, squirt a few drops

of pneumatic tool lubricant into the air input fitting,

before commencing testing.



Air volume is just as important as air pressure.

The air volume that is delivered to the air stapler

may be insufficient due to defective couplings

and crimped hoses, or through the effect of

contamination and water in the system. The

consequence of a restricted airflow is that the air

stapler receives an inadequate air volume, even

though the air pressure reading is high. This will

lead to defective operation, through reduced

driving power.

Before you begin with troubleshooting, you should

first inspect the path from compressor to air

stapler for restricted connections, twisted hoses

and anything else that might prevent sufficient air

from flowing to the appliance.



Frequent, but not excessive, lubrication is

essential for optimum functioning. Oil injected

from an oil mist lubricator will lubricate the internal

parts continuously. Use a lubricant for pneumatic

tools, Mobil Velocite #10, or equivalent. Use no

cleaning oil or additives, as these lubricants can

cause accelerated wear of seals and edges in the

appliance, resulting in a poor performance and

frequent maintenance of the tool.

Please use Airline Lubricating Oil into

the air inlet on the handle of the

Airstapler.

When there is no oil mist lubricator available,

add oil via the QD coupling once or twice a day,

while using. Just a few droplets of oil each time is

sufficient. Excessive oil will simply accumulate in

the appliance, which will become noticeable when

tacking.



With operation during cold weather, close to

or below freezing point, moisture in the air

pipeline can freeze, making use of the appliance

impossible. We recommend the use of a special

winter lubricant for pneumatic tools, or the

permanent use of antifreeze (glycol) as lubricant

when the temperatures are low.

Avoid storing the tool in a cold

environment, to prevent frost or ice

formation on the operating valves and

mechanisms, which might cause

malfunction of the appliance.

Some commercial dehydrating fluids for

air pipelines are harmful to O-rings and seals. Do

not use these desiccants for low temperatures

without being certain of compatibility.



To prevent damage in transit, the machine is

delivered in sturdy protective packaging. The

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm ATM1042 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info