Bedienungsanleitung Ferm BCM1022 (Seite 11 von 24) (Englisch)

763649

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Installing cutting head

1. Put the angled bar into the side holes of the

gear case and the plate so as to fasten the axle.

2. Mount the trimmer head on the axle. Fasten

tightly anti-clockwise.

Before using the trimmer head, mount

the trimmer knife to protection shield with

3 screws (fig. 7). When the machines is

running, tap the trimmer head on the

ground, and trimmer line will come out

automatically. The trimmer knife will cut

and keep the trimmer line in the correct

length.

Harness

Fig. 8, 9, 10

Always wear the provided harness when

using the machine!

Always make sure the machine is hooked

securely to the harness. If you don’t, you

will be unable to control the machine

safely. This can result in injury to yourself

or others.

Never use a harness with a defective

quick release or any other damage.

Wear the provided harness without

twisted bands, with the hanger on your

right side.

Balance the harness

1. Hook your machine to the hanger.

2. Adjust the bands of the harness to have the

blade parallel to the ground when standing in

your normal working position to provide you

most effectiveness and comfort on operating

the machine.

3. In order to prevent the hanger position to

change during operation, turn up the extra part

of the band from the buckle.

4. When correctly adjusted, check the correct

working of the harnesses quick release.

Fuel

Fig. 11

Gasoline is very flammable. Avoid smoking

or bringing any flame or sparks near fuel.

Make sure to stop the engine and allow it

cool before refueling the unit. Select

outdoor bare ground for fueling and move

at least 3 m (10 ft) away from the fueling

point before starting the engine.

Fuel Mixture

The engines are lubricated by oil specially

formulated for air-cooled 2-cycle gasoline engine

use. Use quality oil expressly labeled for air-

cooled 2-cycle engine use. Do not use BIA or

TCW (2-stroke water-cooling type) mixed oil.

Recommended mixing ratio is:

GASOLINE 25 : OIL 1

• Exhaust emission are controlled by the

fundamental engine parameters and

components (eq., carburetion, ignition timing

and port timing) without addition of any

major hardware or the introduction of an inert

material during combustion.

• These engines are certified to operate on

unleaded gasoline.

• Make sure to use gasoline with a minimum

octane number of 89RON (USA/Canada: 87AL).

• If you use a gasoline of a lower octane

value than prescribed, there is a danger that

the engine temperature may rise and an

engine problem such as piston seizing may

consequently occur.

• Unleaded gasoline is recommended to reduce

the contamination of the air for the sake of

your health and the environment.

• Poor quality gasoline or oils may damage

sealing rings, fuel lines or fuel tank of the engine.

Mixing Fuel

Always mix petrol and 2-cycle engine oil

only in a container specifically

designated for this purpose.

1. Measure out the quantities of gasoline and oil

to be mixed.

2. Put some of the gasoline into a clean,

approved fuel container.

3. Pour in all of the oil and agitate well.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm BCM1022 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info