Bedienungsanleitung Ferm BGM1003 (Seite 6 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

510132

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

Wear ear and eye protection

wear a dustmask

Keep bystanders away

Special safety instructions

• The following points need to be checked:

• Do the connecting voltage of the machine

correspond with the mains voltage.

• Are the mains lead and the mains plug in a

good condition; strong, without ravels or

damages.

• For functional reasons the turning parts of this

machine are not covered. Therefore it is of

utmost importance to be careful. Hold the

workpiece firmly, to prevent it from slipping

from your hands. Never touch the sanding

surfaces of a working machine with your

hands.

• Avoid the use of long extension cables.

• If necessary, secure the sanding machine with

screws.

Before you operate the machine:

• Always keep the mains cable away from

moving parts of the machine.

• Use safety goggles.

• Use a dust mask.

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the power supply

corresponds to the voltage on the rating

plate.

Replacing cables or plugs

Immediately throw away old cables or plugs

when they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in

the wall outlet.

Using extension cables

Only use an approved extension cable suitable

for the power input of the machine. The minimum

conductor size is 1.5 mm

. When using a cable

reel always unwind the reel completely.

Immediately switch off the machine when:

• Excessive sparking of the carbon brushes and

verticiliosis in the collector.

• Interruption of the mains plug, mains lead or

mains lead damage.

• Defect switch

• Smoke or stench of scorched isolation

3. Before putting the machine

into operation

Installation

Avoid the use of long extension cables. If

necessary, secure the sanding machine on a

working bench with help of screws through the

holes in the feet of the machine frame. Do not

forget to leave enough space around the machine

for the workpieces to be sanded.

Assembly

• Put the machine frame on its head and press

the four rubber stops into the foot of the frame.

• Machine frame, aluminium disc (10) and work

plate (12) are supplied in separate packaging.

• Push the aluminium disc on the shaft and

fasten the disc with the socket bolt in the side

of the disc (Fig.2 - 4).

• Place the work plate (12) with the shaft in the

machine frame and secure the work plate with

the bolt in the side of the machine frame.

Check with a 90° sash angle on the work plate

and against the sanding disc if the angle is

exactly 90° (Fig.5).

• If necessary, adjust this angle with the

calibration indicator.

• The mitre scale (13), which is also supplied

separately, can be placed on the work plate

(12). With the use of this mitre scale the angle

of grinding can be determined precisely.

• The fence (8) for the belt sander can be placed

behind the uppermost bolt of the V-belt guard.

In this way the workpiece can be held firmly

against the belt, without great hazards.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm BGM1003 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info