Bedienungsanleitung Ferm BGM1003 (Seite 7 von 80) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

510132

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

To prevent the workpiece or your fingers

from getting caught between the work plate

(12) and the sanding disc (11), the space

between work plate (12) and sanding disc

(11) must not exceed 1.6 mm.

The choice of sanding paper

With coarse sanding paper (P 60) generally most

of the material can be removed, and fine sanding

paper (P 150) is then used for finishing. An

uneven surface is first treated with coarse sanding

paper and sanded until it is even. Subsequently

medium-coarse sanding paper (P 100) is used to

remove the scratches caused by the first type of

paper used. Fine sanding paper (P 150) is used

for finishing. The sanding needs to be continued

until the surface is smooth.

The placing of the sanding paper

Fig. 6 - 9

When the sanding machine is held with the

sanding disc turned towards you, the sanding

belt moves from right to left along the upper part

of the machine. Because of this turning direction

the workpiece will be pressed against the right

side of the fence. An arrow on the inside indicates

the right direction of running of the sanding belt

(see drawing). If no direction is indicated, the

sanding belt must be placed in such a way that

the elevated part of the seam is placed into the

turning direction of the belt. So it is very important

that the sanding belt is placed in the correct

way. The machine uses standard 100 x 915 mm

sanding belts (nr 7):

• Remove the plug from the mains socket.

• Push the clamping handle completely to the

right to take away the tension of the transport

rollers (Fig.1: 14).

• Push the sanding belt along both of the

transport rollers, starting from the back of the

machine.

• Push the clamping handle completely to the

left. Now the sanding belt should be

completely tight.

• Turn the transport roller exactly in a right angle

to the direction of the sanding belts with the

use of the winged nut at the right roller. The

direction of running of the belt is adjusted

correctly if the sides of the sanding belt are

running parallel to the bearing plate.

The sanding disc

Paper or “velcro” plates are used for the sanding

disc. The standard diameter is 150 mm. The

plates are self adhesive.

Vertical placing of the sanding belt

For more flexibility of the sanding belt its bottom

side can be used, because there is no bearing

plate. For an easy reach of this bottom side the

sanding belt can be placed in vertical position.

• Loosen the two nuts at the front of the sanding

machine, around the left transport roller shaft,

with the use of an open-end spanner.

• Push the sanding belt up in the position

desired.

• Fasten the two nuts again.

• The workpiece can now rest on the worktop

instead of on the sanding belt;

• The work plate which is used for the sanding

disc can now be pushed with the shaft into the

hole of the machine frame, at the left side of

the sanding machine.

• Fasten the bolt at the back of the machine.

• The work plate can now be used as support

for the sanding of the work piece against the

sanding belt.

4. Putting the machine into operation

Switching On/Off

• Press the switch into position ‘1’ to put your

sanding machine into operation.

• To switch off the machine the same switch

needs to be pressed to position ‘0’.

• Always keep the mains cable away from

moving parts.

• There is no need to apply any pressure with

the workpiece, because this only slows down

the speed of the sanding disc.

Sanding

The sanding belt and disc supplied with this

sanding machine are suitable for the sanding of

metal, wood or synthetic surfaces. The workpiece

should always be held firmly during sanding. No

extra pressure is needed. Guide the work piece

up and down over the sanding belt, in order to

prevent the sanding belt and plate from wearing

through in one place. Round objects can be

sanded at the ends of the sanding belt. Work

pieces which are longer than the sanding machine

can be sanded by removing the fence.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm BGM1003 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info