Bedienungsanleitung Ferm BJM1009 (Seite 6 von 136) (Alle Sprachen)

762274

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

- using the tool for different applications, or with

different or poorly maintainted accessories,

may significantly increase the exposure level

- the times when the tool is switched off or when

it is running but not actually doing the job, may

signifi cantly reduce the exposure level

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work

patterns.

2. SAFETY INSTRUCTIONS

Explanation of the symbols

Denotes risk of personal injury, loss of life

or damage to the tool in case of non-

observance of the instructions in this

manual.

Indicates electrical shock hazard.

Immediately unplug the plug from the

mains electricity in the case that the cord

gets damaged and during maintenance.

Keep bystanders away

Special safety instructions

• Sawdust and splinters must not be removed

while the machine is running.

• Do not use cutting discs or circular saw blades

in the machine.

• Protect saw blades against shocks and

impacts.

• Only use properly sharpened blades,

otherwise increased cutting forces will shatter

the work piece.

• Before use, inspect the saw blade for any

damage. Do not use saw blades which are

cracked, ripped or otherwise damaged.

• Make sure that the work piece is sufficiently

supported or clamped. Keep your hands away

from the surface to be cut.

• Use the machine only with the auxiliary handle

• When saw blades have to be mounted on

the thread of the spindle, make sure that the

spindle has sufficient thread.

• Make sure that the saw blade has been

mounted and fastened properly. Do not use

reducing rings or adapters to make the saw

blade fit properly.

• Apply the machine to the work piece only

when the machine is switched on.

• When working with the machine always

hold the machine firmly with both hands and

provide for a secure stance.

• Persons under 16 years of age are not

permitted to operate this machine.

• Always wear safety goggles and hearing

protection. If desired or required also use

another protection for example an apron or

helmet.

• Always disconnect the plug from the socket

before carry out any work on the machine.

Only plug-in when the machine is switched off.

• Keep mains lead clear from working range

of the machine. Always lead the cable away

behind you.

• Do not stop the blade by hand after switching

off.

• The base plate must not be clamped down

while the blade is extended. Lowering and

raising the blade must be a smooth operation.

• Always use the protective shields on the

machine.

• Use only cutting discs whose allowable speed

is at least as high as the highest no-load speed

of the machine.

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the power supply

corresponds to the voltage on the rating

plate.

Your machine is double insulated in

accordance with EN 60745; therefore no

earthwire is required.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm BJM1009 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info