Bedienungsanleitung Ferm BJM1009 (Seite 8 von 136) (Alle Sprachen)

762274

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Make sure that the top of the base plate

is securely closed before operating the

machine.

Mounting the dust bag

Fig. A

• For dust extraction the dust bag (13) can be

used. Connect the dust extraction adapter (12)

to the machine, then connect the dust bag (13)

to the adapter.

• Empty the dust bag regularly so that the

vacuuming performance remains intact.

• A vacuum cleaner can be directly connected

to the dust extraction adapter when use of a

vacuum cleaner is preferred.

5. OPERATION

Never use the spindle lock while the

machine is running.

Switching on and off

Fig. A

• To switch the machine on slide the on/off

switch (1) forwards.

• To switch the machine off, depress the on/off

switch (1), the switch will automatically move

to the ‘off’ position.

Never use the spindle lock to stop the

motor.

Marking the workpiece

Fig. E

Before starting with the Biscuit Jointer the

workpieces must be marked as following.

• Place the two surfaces which must be

connected, with their connecting side to each

other

• Clamp the work pieces and mark the center of

the groove by drawing a perpendicular line

• Several joints will be required for larger

workpieces. The distance between two drawn

lines should be at least 10cm.

Sawing grooves

Fig. F

• Set and check the cutting depth on the

machine

• Set the angle on the machine

• Set the height on the machine, take care for

setting the height, the groove for the biscuit

dowel must be in the middle of the workpiece.

• Make sure the workpiece is securely clamped

• Position the machine on the workpiece, the

marked centerline (15) must be in line with the

line drawn on the workpiece

• Hold the machine with both hands and switch

the machine on.

• Push the motor base carefully forward as far

as possible.

• Move the motor base backward and switch the

machine off.

For workpieces thinner than 16 mm it is

not possible to cut the groove in the

middle of the workpiece without adding

an adjustment plate below your

workpiece (fig. G).

Joining the workpieces

When the grooves in both workpieces have been

made the workpieces can be joined together.

• Put glue in both grooves.

• Place the biscuit dowel in the groove of one

workpiece.

• Place the other workpiece on the biscuit

dowel.

• Fasten the workpieces and wait till the glue is dry.

User tip for connecting two workpieces

• Saw a groove as big as one biscuit into the first

workpiece

• Place the biscuit with good glue (according the

material) into the groove

• Saw a longer groove into the other workpiece

• Now both workpieces can be positioned easily

towards each other (clearance to correct)

• Fasten the workpieces and wait till the glue is dry

Move the machine in the same direction

as the direction of rotation. See arrow on

top of the machine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm BJM1009 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info