Bedienungsanleitung Ferm BJM1009 (Seite 7 von 136) (Alle Sprachen)

762274

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

Replacing cables or plugs

Immediately throw away old cables or plugs

when they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in

the wall outlet.

Using extension cables

Only use an approved extension cable suitable

for the power input of the machine. The minimum

conductor size is 1.5 mm2. When using a cable

reel always unwind the reel completely.

3. ADJUSTING THE MACHINE

Adjusting the cutting depth

Fig.B

• Move the motor housing (3) as far as possible

backwards.

• Set the cutting depth by turning the cutting

depth adjustment knob (9).

• The markings on the depth adjustment knob

(9) correspond to the biscuit dowel size being

used (16).

• You can fine adjust the cutting depth setting by

turning the depth fine adjustment screw (10).

• Move the motor base forwards and check if

depth fine adjustment screw (10) will fall in the

notch of the adjustment knob.

The following table shows the relationship of

the markings on the adjustment knob to cutting

depth, thickness of material and associated

biscuit dowel.

Marking Thickness Biscuit Cutting

of material Dowel depth in mm

0 8-12 mm No. 0 8.0

10 12-15 mm No. 10 10.0

20 > 15 mm No. 20 12.3

Max. - - 14.0

Adjusting the cutting angle

Fig. A + G

The cutting angle can be set the following way:

• Release the angle adjustment knob (6) by

turning it anti-clockwise

• The set angle is shown on the scale (21) below

the knob (6)

• After setting to the right angle, tighten the

knob (6) again by turning it clockwise.

Adjusting the height to match material

thickness

Fig. B

The correct height can be set the following way:

• Release the height adjustment knob (8) by

turning it anti-clockwise

• The set height is shown by the scale and the

arrow (22).

• After setting to the right height, tighten the

knob (8) again by turning it clockwise.

The height must correspond to half of the material

thickness of the working piece, the groove for the

biscuit dowel must always be in the middle of the

working piece.

4. MOUNTING ACCESSORIES

Prior to mounting an accessory always

unplug the tool.

How to change the saw blade

Your machine is delivered with the saw

blade already assembled on the machine

Fig. C & D

• Put the machine in upside-down position and

remove the 4 screws on the bottom plate by

using a screw driver (not included)

• Remove the bottom plate (20)

• Press the spindle lock (5) and turn the spindle

until it engages in the lock. Keep the spindle

lock pressed during this procedure.

• Remove the flange nut (17) from the spindle

by using the spanner (14) and turn it

counterclockwise.

• Position the saw blade (18) on the flange (17).

• Be aware that the arrow on the sawblade

indicates the same direction as the arrow on

the inside of the housing.

• Place the flange nut (17) on the spindle and

tighten it with the wrench.

• Take care the flange nut (17) will be placed the

correct way: The collar side must fit inside the

saw blade bore, the flat side must be pointing

upwards.

• Release the spindle lock and check that the

spindle is unlocked by rotating it.

• Assemble the bottom plate (20) again and fix

the 4 screws.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm BJM1009 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info