764187
6
Zoom out
Zoom in
Vorherige Seite
1/92
Nächste Seite
6Ferm
EN - Useanesandingbelt(grain120)for
nishingsurfaces.
● Makesurethatthesandingbelt(12)isstraight
and centred around the sanding pad (3) and
the sanding belt rollers (4).
● Tightentheclampinglever(5).
Removing
● PlacethemachineonitssidewiththeV-belt
cover (11) facing downwards.
● Releasetheclampinglever(5).
● Removethesandingbelt(12).
● Tightentheclampinglever(5).

If the sanding belt does not run parallel with the
outer edge of the housing, the sanding belt must
be centred.
● Turnthecentringknob(6)clockwisetomove
the sanding belt (12) to the inside.
● Turnthecentringknob(6)counterclockwiseto
move the sanding belt (12) to the outside.
USE

● Toswitchonthemachine,presstheon/off
switch (1).
● Toswitchthemachinetocontinuousmode,
keep the on/off switch (1) pressed and
simultaneously press the lock-on button (2).
● Toswitchoffcontinuousmode,pressthe
on/off switch (1) again.
● Toswitchoffthemachine,releasetheon/off
switch (1).

● Insertthedustbag(13)intothedustbag
connection (9).
Hints for optimum use
● Clamptheworkpiece.
● Holdthemachinewithonehandonthemain
grip and the other hand on the auxiliary grip.
● Switchonthemachine.
● Placethesandingbeltontheworkpiece.
● Slowlymovethemachineovertheworkpiece,
rmlypressingthesandingbeltagainstthe
workpiece.
● Donotapplytoomuchpressureonthemachine.
Let the machine do the work.
● Switchoffthemachineandwaitforthemachine
to come to a complete standstill before putting
the machine down.
CLEANING AND MAINTENANCE
3 Before cleaning and maintenance,
always switch off the machine and
remove the mains plug from the mains.
● Regularlycleanthehousingwithasoftcloth.
● Keeptheventilationslotsfreefromdustand
dirt. If necessary, use a soft, moist cloth to
remove dust and dirt from the ventilation slots.
● Regularlycleanthesandingpadandthe
sanding belt rollers to avoid inaccuracies
during use.

● Toremovetheoldsandingbelt(12),proceed
asdescribedinthesection“Mountingand
removing the sanding belt”.
● Tomountthenewsandingbelt(12),proceed
asdescribedinthesection“Mountingand
removing the sanding belt”.
Checking and replacing the carbon brushes

The carbon brushes must be checked regularly.
If the carbon brushes are worn, the machine will
start to run unevenly.
2 Only use the correct type of carbon
brushes.
● Removethecarbonbrushholders(10)using
a screwdriver.
● Cleanthecarbonbrushes.
● Incaseofwear,replacebothcarbonbrushes
at the same time.
● Mountthecarbonbrushholders(10)using
a screwdriver.
● Aftermountingthenewcarbonbrushes,
let the machine run at no load for 15 minutes.
WARRANTY
Consult the enclosed warranty terms.
ENVIRONMENT
Disposal
The product, the accessories, and the packaging
must be sorted for environmentally friendly
recycling.
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Ferm BSM1023 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info