Bedienungsanleitung Ferm CSM1045 (Seite 15 von 28) (Englisch)

763696

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Before proceeding to your job, read the

section “Sefety Instructions”. It is

recommended to first practice sawing

easy logs. This also helps you get

accustomed to your unit.

Always follow the safety regulations. The

chain saw must only be used for cutting

wood. It is forbidden to cut other types

of material. Vibrations and kickback vary

with different materials and the

requirements of the safety regulations

would not be respected.

Do not use the chain saw as a lever for

lifting, moving or splitting objects. Do not

lock it over fixed stands. It is forbidden to

hitch tools or applications to the PTO

other than those specified by the

manufacturer.

It is not necessary to force the saw into

the cut. Apply only light pressure while

running the engine at full throttle.

When the saw chain is caught in the cut,

do not attempt to pull it out by force, but

use a wedge or a lever to open the way.

This saw is equipped with a chain brake

that will stop the chain in the event of

kickback if operating prop¬erly. You

must check the chain brake operation

before each usage by run¬ning the saw

at full the throttle for I ¬2 seconds and

pushing the front hand guard forward.

The chain should stop immediately with

the engine at full speed. If the chain is

slow to stop or does not stop, replace

the brake band and clutch drum before

use.

It is extremely important that the chain

brake be checked for proper operation

before each use and that the chain be

sharp in order to maintain the kickback

safety level of this saw. Removal of the

safety devices, inadequate maintenance,

or incorrect replacement of the bar or

chain may increase the risk to serious

personal injury due to kickback.

General guidelines for felling trees

Never cut with the nose of the guide bar.

Danger of kickback.

Felling can start only under the condition

that an escape route from the felling tree

is provided.

When you fell a tree, be sure to warn

neighboring workers of the danger.

Never cut a tree during winds.

Always ensure your foothold. Do not

stand on the log.

Be alert to the rolling over of a cut log.

Especially when working on a slope,

stand on the uphill side of the log.

Follow the instructions in “Safety

Instructions” to avoid kickback of the

saw.

• In the area of felling trees, there must not be

any other persons or animals.

• The safety distance from the tree being felled

is minimally 2½ x the length of the tree.

• The direction of the fall is controlled by the

notching cut.

• The escape route should lead ca 45° obliquely

back.

• For the direction of the tree fall, these factors

are also important:

- Natural lean of the tree,

- Height of the tree,

- Large amount of branches,

- Location on flat land or slope,

- Asymmetric growth, damaged wood,

- Direction and velocity of air,

- Snow on the branches.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CSM1045 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info