Bedienungsanleitung Ferm CSM1045 (Seite 14 von 28) (Englisch)

763696

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Keep clear of the saw chain as it will start

rotating upon starting of engine.

1) Fill fuel and chain oil tanks respectively, and

tighten the caps securely.

2) Set the switch to “I” position.

3) Pull out the choke knob to the closed position.

4) While holding the saw unit securely on the

ground, pull the starter rope vigorously.

5) When engine has ignited first, pull the throttle

lever to return the choke knob to the open

position and then pull the starter again to start

the engine.

6) Allow the engine to warm up with the throttle

lever pulled slightly.

Switching off the engine

1) Release the throttle lever to allow the engine to

idle for a few minutes.

2) Set the switch to the “O” (STOP) position.

Chain oil

Fig. 6a

Make sure to set up the bar and the

chain when checking the oil supply. If

not, the rotating parts may be exposed. It

is very dangerous.

After starting the engine, run the chain at medium

speed and see if chain oil is scattered off as

shown in the figure 6a.

Chain oil flow adjusting

Fig. 6b

The chain oil flow can be changed by inserting a

screw-driver in the hole on bottom of the clutch

side. Adjust according to your work conditions.

The oil tank should become nearly empty

by the time fuel is used up. Be sure to

refill the oil tank every time when

refueling the saw.

Carburetor

Fig. 7

Be sure to adjust the carburetor with the

bar chain attached.

The carburetor on your unit has been factory

adjusted, but may require fine tuning due to a

change in operating conditions. Before adjusting

the carburetor, make sure that the provided

air/fuel filters are clean and fresh and the fuel

properly mixed.

When adjusting, take the following steps:

1) H and L needles are restricted within the

number of turn as shown below.

H needle: -1/4 -1/4

L needle: -1/4 -1/4

2) Start the engine and allow it to warm up in low

speed for a few minutes.

3) Turn the idle adjusting screw counterclockwise

so that the saw chain does not turn. If the idling

speed is too slow, turn the screw clockwise.

4) Make a test cut and adjust the H needle for

best cutting power, not for maximum speed.

Chain brake operational test

Fig. 8

Test the chain brake periodically to

ensure correct function.

• Place the saw on a clear, firm, flat surface and

then start the engine.

• Grasp the rear handle with your right hand and

with your left hand, hold the front handle safely

and firmly.

• Let the engine run at mid revs.

• Squeeze the chain brake lever to the front. The

saw chain should abruptly stop.

• Then depress the trigger to “IDLE” and release

the chain brake.

If the chain does not stop, turn the

engine off and take your unit to the

nearest authorized service centre for

service. The saw must not be used.

WORKING INSTRUCTIONS

Felling requires extensive experience.

Both, felling and limbing must only be

carried out by trained persons.

Courses for working with chainsaws and

courses for felling trees are regularly

offered by local professional

organisations.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CSM1045 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info