Bedienungsanleitung Ferm CSM1045 (Seite 13 von 28) (Englisch)

763696

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

4) Pour in the rest of gasoline and agitate again

for at least one minute. As some oils may be

difficult to agitate depending on oil ingredients,

sufficient agitation is necessary for the engine

to last long. Be careful that, if the agitation is

insufficient, there is an increased danger of early

piston seizing due to abnormally lean mixture.

5) Put a clear indication on the outside of the

container to avoid mixing up with gasoline or

other containers.

6) Indicate the contents on outside of container

for easy identification.

Shake the mixture correctly before

pouring it into the fuel tank.

Fuel Storage

Fuel can be stored for a limited time period only.

Fuel and mixtures get old. Old fuel mixture can

cause problems during starting of the chainsaw.

Mix only as much of the mixture as you need for

the following 4 week period.

Fueling the unit

Fig. 4

1) Untwist and remove the fuel cap. Rest the cap

on a dustless place.

2) Put fuel into the fuel tank to 80% of the full

capacity.

3) Fasten the fuel cap securely and wipe up any

fuel spillage around the unit.

Select flat and bare ground for fueling.

Move at least 10 feet (3 meters) away

from the fueling point before starting the

engine.

Stop the engine before refueling the unit.

At that time, be sure to sufficiently

agitate the mixed gasoline in the

container.

Saw chain oil

Fig. 4

Use motor oil SAE #10W-30 all year round or SAE

#30 ~ #40 in summer and SAE #20 in winter.

Do not use wasted or regenerated oil

that can cause damage to the oil pump.

To enable sufficient oil lubrication of the saw

chain, there must be a sufficient amount of oil in

the tank.

Whenever filling the fuel mixture to the

tank, also replenish the oil for saw

chains.

To oil the chain saw and guide bar, use only

ecological, biologically degradable oil for saw

chains, then eventually oil for saw chains on the

basis of mineral oils (ISO VG 100).

Oils for saw chains stick when not used

for a long time. This can cause damage

to the oil pump or parts using the oil.

How to avoid it:

• Empty the oil for saw chains out of the oil tank

of the chain saw.

• Replenish the tank with a little engine oil.

• Allow the chain saw to run for some time

to enable the oil to flow and to clean the oil

pump.

Before further use of the chain saw, again

replenish the tank with oil for saw chains.

4. OPERATION

Engine start

Fig. 4, 5a, 5b

Before starting the saw be sure to loosen

the chain brake. The safety cover should

be pulled to the front handle.

It is very dangerous to run a chainsaw

that mounts broken parts or lacks any

parts. Before starting engine, make sure

that all the parts including bar and chain

are installed properly.

When restarting immediately after

stopping the engine, leave the choke

knob at the open position.

When restarting immediately after

stopping the engine, leave the choke

knob at the open position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CSM1045 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info