Bedienungsanleitung Ferm CSM1045 (Seite 11 von 28) (Englisch)

763696

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Mass (without guide bar and

chain and with empty tank) 6.2kg

Guaranteed sound power level,

LWA (2000/14/EC) LwA: 117 dB(A)

Level of sound pressure LPA 101 dB (A)

Vibration acceleration avhw 9.68 m/s2

Vibration level

The vibration emission level stated in this

instruction manual has been measured in

accordance with a standardized test given in

EN60745; it may be used to compare one tool

with another and as a preliminary assessment of

exposure to vibration when using the tool for the

applications mentioned.

• Using the tool for different applications, or with

different or poorly maintained accessories,

may significantly increase the exposure level.

•

The times when the tool is switched off or when

it is running but not actually doing the job, may

significantly reduce the exposure level.

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work patterns.

Description

The numbers in the text refer to the diagrams on

pages 2-7

1. Saw chain

2. Guide bar

3. Fuel tank cap

4. Front handle

5. Primer (starter pull rope)

6. Air filter cover

7. Starter grip

8. Choke knob

9. Switch

10. Throttle trigger interlock

11. Guide bar cover

12. Oil tank cap

13. Starter cover

14. Saw chain tensioner screw

15. Chain brake

16. Spike bar

17. Bar retaining nuts

18. Chain catcher

19. Muffler

20. Throttle trigger

21. Rear handle

3. ASSEMBLY

Guide bar and saw chain assembly

Fig. 2a - 2d

The saw chain has very sharp edges. Use

thick protective gloves for safety.

Before starting any work on the guide

bar and the saw chain:

• Stop the engine,

• Unplug the spark plug connector,

• Put protective gloves on.

• Observe the run direction of the saw chain.

• The cutting edges of the saw teeth on the top

side of the guide bar lead to the front to the

reversible star (the end of the bar).

1) Pull the guard towards the front handle to

check that the chain brake is not engaged.

2) Loosen the nuts and remove the chain cover.

3) Install the attached spike to the power unit.

4) Gear the chain to the sprocket and, while

fitting the saw chain around the guide bar,

mount the guide bar to the power unit. Adjust

the position of chain tensioner nut on the chain

cover to the lower hole of guide bar.

Pay attention to the correct direction of

the saw chain.

5) Fit the chain cover to the power unit and fasten

the nuts to finger tightness.

6) While holding up the tip of the bar, adjust the

chain tension by turning the tensioner screw

until the tie straps just touch the bottom side

of the bar rail.

7) Tighten the nuts securely with the bar tip

held up (12 ~ 15 Nm). Then check the chain

for smooth rotation and proper tension while

moving it by hand. If necessary, readjust with

the chain cover loose.

8) Tighten the tensioner screw.

A new chain will expand its length in the

beginning of use. Check and readjust the

tension frequently as a loose chain can

easily derail or cause rapid wear of itself

and the guide bar.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm CSM1045 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info