Bedienungsanleitung Ferm FDAG 750 (Seite 6 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

79094

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Ferm

Fasten the side handle for left-hand operation •

on the right-hand side of the machine.

Fasten the side handle for right-hand operation •

on the left-hand side of the machine.

Make sure that the side handle is

fastened properly and cannot loosen

unexpectedly.

Mounting the guard

Fig. 2

Mount the guard before using the machine.

Assembly

Place the guard (2) on the housing. Be aware •

that the notch of the guard falls across the edge

of the housing.

Place the fixing-ring (7+12) on the guard: the •

ring-holes have to be on the screw-holes.

Mount the guard en fixing-ring with help of the •

4 screws and washers (8).

The closed side of the guard always has to •

point in the user’s direction.

Be aware the screws are tightened well

enough. Check regularly if the screws

are still fixed.

Disassembly

Remove the flange nut and the grinding disc •

with lower flange from the spindle.

Unscrew the 4 screws (with washers) en •

remove the fixing-ring.

Remove the guard from the machine.•

•

Mounting a grinding disc

Fig. 3

Use grinding discs of the correct dimension. Use

fibre reinforced grinding discs only. The grinding

disc must not touch the edge of the guard.

Remove the plug from the mains

Press the spindle lock (Fig. 1 - 5) and turn the •

spindle (6) until it engages in the lock. Keep the

spindle lock pressed during this procedure.

Remove the flange nut (10) from the spindle •

using the spanner (11).

Position the grinding disc on the flange (9).•

Place the flange nut on the spindle and tighten •

it using the spanner.

Release the spindle lock and check that the •

spindle is unlocked by rotating it.

Mounting grinding discs and roughing discs

Fig. 4 and 5 show how to mount the flange (10)

when using thick (4 – 8 mm) and thin (2,5 – 4 mm)

discs.

4. USE

Always observe the safety instructions

and applicable regulations.

Special attention when starting the machine

Clamp the workpiece and make sure that the •

workpiece cannot slide from under the machine

during the cutting activities.

When working with the machine, always hold it •

firmly with both hands and provide for a secure

stance.

Always direct the cable to the rear away from •

the machine.

Insert the mains plug only when the machine is •

switched off.

Apply the machine to the workpiece only when •

switched on

Never use the machine for grinding

magnesium workpieces.

Switching on and off

Slide the on/off switch forwards.•

To switch off, depress the on/off switch, this will •

then jump to the ‘off’ position.

Do not put the machine down when the

motor is still running. Do not place the

machine on a dusty surface. Dust

particles may enter the mechanism.

Operation

Hold the machine firmly and move it against the •

workpiece. Move the grinding disc evenly

across the workpiece.

Move the machine during roughing under an •

angle of 30º - 40º across the workpiece (Fig. 6).

Never use grinding discs for roughing!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm FDAG 750 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info