Bedienungsanleitung Ferm FDAG 750 (Seite 7 von 52) (Deutsch, Englisch, Holländisch, Französisch, Italienisch)

79094

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Ferm

The machine must always work opposite to the •

direction of rotation. Therefore, never move the

machine in the other direction! Otherwise, the

danger exists of it being pushed uncontrolled

out of the cut (Fig. 7).

Inspect the grinding disc regularly. Worn discs •

have a negative effect on efficiency of the

machine. Replace the grinding disc on time.

Do not put the machine down when the motor •

is still running. Do not place the machine on a

dusty surface. Dust particles may enter the

mechanism.

Always switch off the machine first before •

removing the plug from the wall socket.

Never use the spindle lock to stop the

motor.

5. SERVICE & MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

This machine has been designed to operate over

a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Cleaning

Keep the ventilation slots of the machine clean to

prevent overheating of the engine. Regularly clean

the machine housing with a soft cloth, preferably

after each use. Keep the ventilation slots free from

dust and dirt. If the dirt does not come off use a

soft cloth moistened with soapy water. Never use

solvents such as petrol, alcohol, ammonia water,

etc. These solvents may damage the plastic parts.

Lubrication

The machine requires no additional lubrication.

Trouble shooting

Below we have listed a few probable causes and

solutions to which you can refer if your circular

saw does not function properly.

1. Machine fails to operate.

Power turned off.•

(Extension) cable damaged.•

2. The elektromotor hardly reaches maximum

speed.

The extension cable is too thin and/or too long.•

The mains voltage is lower than 230 V.•

3. Machine overheats.

Air vents are blocked. Clean them with a dry •

cloth.

The machine has been overloaded. Use the •

machine for the purpose it is made for.

4. Excessive sparking or elektromotor runs

irregular.

There’s dirt inside the motor or the carbon •

brushes are worn.

Replace the carbon brushes or bring the •

machine to a specialized repair centre.

Faults

Should a fault occur, e.g. after wear of a part,

please contact the service address on the

warranty card. Separately you will find an

exploded view showing the parts that can be

ordered.

Environment

To prevent damage during transport, the appliance

is delivered in a solid packaging which consists

largely of reusable material. Therefore please

make use of options for recycling the packaging.

Damaged and/or disposed of electrical

or electronic devices must be dropped

off at recycling stations intended for that

purpose.

Warranty

For the conditions of warranty, please refer to the

separately provided warranty card.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm FDAG 750 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info