Bedienungsanleitung Ferm GRM1026 (Seite 7 von 40) (Englisch, Französisch, Türkisch)

763929

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

circulation will damage the sealing rings of the

machine.

• It is necessary to turn on the spray lance within

one or two minutes after the machine has been

started. Otherwise, the temperature of the

circulating water within the machine will soon

rise to a critical point, which will cause damage

to the sealing rings inside the machine.

• Don’t start and run the machine in a place

excessively cold so as to prevent the machine

from the freezing current.

• This machine has been designed for only using

cleaning water, do not use corrosive chemicals.

• Use cleaning agent supplied or recommend by

the manufacturer.

• High-pressure jets can be dangerous if subject

to misuse. The jet must not be directed at

persons, animals, live electrical equipment or

the machine itself. Pressure washers should

not be pointed at tire walls, as it may be

possible to damage them.

• Do not direct the jet against yourself or others

in order to clean clothes or footwear.

• Disconnect from the electrical power supply

before carrying out user maintenance.

• If the mains cable is damaged it must be

replaced by the manufacturer, or its service

agent or similarly qualified person to avoid a

hazard.

• Do not use the machine if a supply cord or

important parts are damaged, e.g. safety

devices, high pressure hoses, trigger gun.

• Be aware of the recoil caused by the water jet

when the machine is switched on.

• When the machine is moving and installing,

the machine must be in flat. When moving the

machine, pulling the handle to move it.

• Connect to the water supply. The machines

are not suitable for connection to portable

water mains. Connect the machine to the water

supply. (It can be a water container).

• Make sure the inlet water pressure keeps

between 0.01MPa and 1.2MPa.The inlet pipe

should at least 5 M long. Do not use the pipe if

the pipe is damaged. If you want connect this

machine to portable water mains, you must

install a backflow preventer in the water pipe

to prevent dirty water flow back to the drinking

water system. The backflow preventer shall

comply with EN 60335-2-79 ANNEX AA.

3. ASSEMBLY

The motor of this pressure washer will

NOT run. It will only operate when the

trigger is squeezed.

CAUTION! The cleaner must only be

used with clean water; use of unfiltered

water or corrosive chemicals will damage

the cleaner.

Assembly of the handle

Fig. 5

• Assemble handle like shown on Fig. 5

• Tighten the screws

Assembly of the nozzle holder, spray gun

holder, cable holder

Fig. 6

• Install the cable holder like shown on Fig. 6

•

Install the spray gun holder like shown on Fig. 6

•

Assemble the nozzle holder like shown on Fig. 4

• Tighten the screws of the nozzle holder

Turning on

• Turn the motor switch to the “OFF/0” position.

• Check that the electrical supply voltage and

frequency (Volts/Hz) correspond to those

specified on the cleaner data plate.

• Ensure that you have a suitable water supply

to feed the pressure washer.

• Connect the outlet hose to the washer and

connect the spray gun to the outlet hose.

• Connect lance and possibly lance extension.

• Check gauze filter is clear of any blockage.

• Connect the water supply hose.

• Check that the hose has no kinks in it.

• Turn on water and check for leaks.

• Squeeze trigger to allow air to be expelled

though the pump and hoses, lock trigger.

• Plug in machine and turn on switch.

• Unlock trigger and use the pressure washer.

Shut down

• Turn off the motor (turn switch to the off position).

• Unplug the unit from the power source.

• Turn off the water supply.

• Press the trigger of the gun to depressurize the

system.

• Disconnect the garden hose from the pressure

washer.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm GRM1026 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info