Bedienungsanleitung Ferm MSM1033 (Seite 6 von 56) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

510117

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

6 Ferm

28. Box spanner

29. Allen key

30. Dust bag

31. Fuse box

Check the machine, loose parts and accessories

for any transport damage.

2. Safety

Symbols and meanings

The following symbols are used in these

instructions for use and on the machine:

Class II machine – Double insulation –

You don’t need any earthed plug.

Denotes risk of personal injury, loss of life

or damage to the tool in case of non-

observance of the instructions in this

manual.

Indicates electrical shock hazard.

Immediately unplug the plug from the

mains electricity in the case that the cord

gets damaged and during maintenance

Keep bystanders away

Wear ear and eye protection

Faulty and/or discarded electrical or

electronic apparatus have to be collected

at the appropriate recycling locations.

Specific safety rules for table saws / mitre

saws

• The user of the machine must be instructed in

the use, adjustment and operation of the

machine,

• Make sure of a well-lit and clean and tidy

working area.

• Never use saw blades that are bent, distorted

or in any other way damaged.

• Never use saw blades of HSS steel.

• Never use saw blades that do not meet the

specifications stated in these instructions for

use.

• Never use adapters to mount saw blades with

to large an axle hole.

• Never saw any material other than wood,

woody material, aluminium and plastics.

• Never remove the protective hood. Make sure

that the saw blade is correctly protected by the

protective hood.

• Check that all movable protective parts do not

stick.

• Never saw work pieces in which there are

nails or other metal objects.

• Never switch the machine on when the piece

of work is touching the saw blade.

• Do not start sawing until the machine is

running at full revolutions.

• Make sure that the piece of work is clamped

down. Never try to saw pieces of work that are

too small.

• Never try to slow down the saw blade by

applying counter pressure to the side of the

blade.

• Never leave the machine unattended before

you have switched it off and the saw blade has

stopped rotating.

• Never try to saw round pieces of work with the

bench circular saw.

• Never remove the riving knife from the table

saw. The distance between the saw blade and

the riving knife must not be more than 5 mm

maximum.

• Make sure that dust vacuuming works

properly while working, in connection with the

danger to health caused by breathing in the

dust being produced.

• With the table saw always use a wooden stick

to move the work piece along the saw blade.

• When using the mitre saw, always make sure

that the saw blade is fully protected by the

protective hood.

• When using the table saw, always make sure

that the upper bench surface is fixed properly.

• Take the plug out of the socket when you are

carrying out maintenance of the machine. The

same goes for assembly or setting up.

• Do not use the machine before you have

assembled and installed it completely as

described in these instructions for use.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm MSM1033 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info