Bedienungsanleitung Ferm MSM1033 (Seite 7 von 56) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

510117

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Ferm

• When you have finished using the machine,

take the plug out of the socket and clean the

bench.

Additional safety instructions

1. When using the saw blades with hard metal

teeth (Carbon tipped) it is advisable to use

blades with a negative or slightly positive

cutting angle. Do not use any saw blades with

deeply cut teeth. They can grip the protective

cap.

2. Attention: First carefully assemble all the parts

before starting work. Follow the procedure as

indicated.

3. If you are not familiar with using such a

machine, you would be better to be informed

first by a professional, an instructor or by a

technician.

4. Always clamp or press the workpiece firmly

against the saw guide, before you carry out

the process. The use of all possible clamping

set-ups is preferable to using your hands.

5. Important: If you are holding the workpiece by

hand for the process to be carried out, keep a

minimum distance of 100 mm from the saw

blade.

6. Always press the workpiece against the

bench.

7. Keep the saw blade sharp and check regularly

whether it rotates freely without abnormal

vibrations. Replace the saw blade if

necessary.

8. Allow the machine to rotate freely until it

reaches the maximum number of revolutions,

before you start the process.

9. Maintain the air inlets at the back and the

bottom of the bench saw machine and electric

engine for a longer machine life. Dust piles

must be removed.

10. Always lock the different degree set-ups

before you start processing.

11. Only buy suitable saw blades with a number of

revolutions of at least 4500 revolutions per

minute.

12. Only use the correct saw blade. Too small or

too big saw blades are extremely dangerous.

13. Regularly inspect the saw blade for any faults.

Replace the saw blade if necessary.

14. Grease the new saw blade and clean the

flanges before you assemble the new blade.

Then assemble the blade in the correct

direction and pull the flanges firmly using the

central bolt.

15. Only use original flanges. All other types are

not suitable.

16. Never work without the protective cap of the

saw blade.

17. The moving part of the protective cap must

also remain assembled.

18. Never grease the saw blade while it is rotating.

19. Always keep your hands removed from the

track of the saw blades.

20. Never pick up the workpiece by grasping with

your hands along or behind the saw blade.

21. Ensure that the workpiece never touches the

saw blade before the machine has been

switched on.

22. Never process metal or stone sorts with this

machine.

23. Use support aids in order to support long

workpieces.

24. Never use the machine in a dangerous

environment, where inflammable gases or

fluids are present.

25. Never leave the machine unattended without

first disconnecting it from the mains voltage.

26. If you hear abnormal noises, try to trace them

or take the machine to a recognized fitter, or

repair company.

27. If a part is broken or damaged, replace it or

repair it immediately.

28. Never stand in the track of the saw blade but

stand to the left or the right of the saw bench.

29. Your hands must likewise be placed next to

the track of the saw blade.

30. Always use the feedstick to push the wood

through the saw.

31. Always place the wood at the front of the saw

bench and then push it further back.

32. For mitring only the adjustable guide must be

used and the fence must be removed.

33. Never use the fence as a linear measure for

cutting off beams.

34. If the saw blade is locked: first switch off the

machine before you attend to the fault.

35. Avoid workpieces hitting back in your direction

by taking the following measures:

• Always use sharp saw blades.

• Do not saw too small workpieces.

• Never release the workpiece before it has

been completely pushed through the saw.

• Always adjust the guide parallel to the saw

blade.

• Never remove the saw protection.

36. Before you continue sawing, ensure that you

are standing firmly and that your hands are in

the required position.

37. Never use thinners to clean the machine. Only

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm MSM1033 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info