Bedienungsanleitung Ferm MSM1033 (Seite 9 von 56) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

510117

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Ferm

You can install the machine in two ways:

a. As a stationary machine on a workbench. In

this case the machine must be secured to the

workbench with 4 bolts.

b. As a stationary machine on the subframe. In

this case the machine must be secured to the

subframe with 4 bolts and the subframe

anchored to the floor or to a floor plate with

dimensions of at least 1 square meter.

Figs. 1 to 4

Make sure that the plug is not in the

socket when assembling and mounting

accessories.

Placement of the machine

Use screws to fix the machine to a sturdy

workbench.

• Place the machine on the workbench and

draw the positions of the holes on the

workbench.

• Drill holes in the marked places of the correct

diameter for the screws to be used.

• Put the machine on the workbench, place the

screws in the mounting holes (11) and screw

the screws tight.

Guide fence insert

For safety reasons, this machine is equipped with

a guide fence insert

to be used when using the machine for sawing

straight cross-cuts.

• For sawing straight cross-cuts, the guide

fence insert must remain mounted on the

machine (fig. 6).

• For sawing mitre cuts, the guide fence insert

must be removed from the machine as shown

(fig. 6).

• For sawing bevel cuts, the guide fence insert

must be removed from the machine as shown

(fig. 7+8).

Mounting the dust bag

In connection with the danger to health by

breathing in any dust released, you must mount

the dust bag (30) on the dust bag connection (5).

This also keeps the workplace cleaner longer.

• Press the clamp of the dust bag and slide it

over the outlet at the rear of the machine. Let

go of the clamp and the dust bag is then fixed

in place.

Parallel and mitre guide (table saw)

Fig. 5

The guide is used to guide the piece of work along

the saw blade. The guide can be mounted to the

left and to the front of the saw blade.

• Slide the guide (17) with the holder into the

guide rail of the bench surface.

• Unscrew the setting screw on the degree arc

(25).

• Move the guide in the rail to the required

place.

• Set the desired angle with the aid of the

degree arc (25):

• parallel sawing: adjusting the guide parallel to

the saw blade

• mitring: setting the guide to the desired angle

in relation to the saw blade

• Screw the setting screw tight again.

• With the aid of the clamp screws (26) the

guide can be moved lengthwise.

Use of the machine:

Mitre saw or table saw

This combined machine can be used in two ways:

mitre saw or table saw. After use the machine

must always be left set up as the table saw.

Set-up for use as a mitre saw

1. Unscrew the screw (4) that locks the upper

bench surface.

2. Keep the saw head pushed downwards

against the handgrip (2), while you bring the

upper bench surface (18) upwards.

3. Screw the screw (4) tight again.

4. Hold the saw head down with your left hand

and pull the lock (8) out with your right hand.

5. Gently let the saw head come upwards.

6. Remove the lower protective hood (16).

7. Put the plug into the socket and test the saw

by pressing the switch (1).

Set-up as a table saw

1. Place the lower protective hood (16) on the

lower bench surface (12) of the cross-cut saw.

2. Hold the operating handgrip (2) firmly with

your right hand. Press the locking knob (3)

with your thumb and bring the saw head

downwards. The saw blade is then completely

protected by the lower protective hood.

3. Lock the lock (8) in place.

4. Unscrew the screw (4) two turns.

5. Push the upper bench surface gently

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm MSM1033 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info