Bedienungsanleitung Ferm PPM1015P (Seite 5 von 36) (Englisch, Holländisch, Französisch, Türkisch)

764213

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Wear a dust mask

Switch off the machine immediately in case of:

• Malfunction in the mains plug, power cable or

damaging of cable.

• Broken switch.

• Smoke or stench of scorched insulation.

Wait for the cutter to stop before setting

the tool down. An exposed cutter may

engage the surface leading to possible

loss of control and serious injury.

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions. Keep these

instructions in a safe place!

Always check that the power supply

corresponds to the voltage on the rating

plate.

Class ll machine. Your machine is double

insulated; therefore no earthed wire is

required.

When replacing old cables or plugs

Throw away old cables or plugs immediately

as soon as new ones have replaced these. It is

dangerous to put the plug of a loose cable into the

socket outlet. When using extension cables Only

use an approved extension cable that is suitable

for the machine’s power. The cores must have a

diameter of at least 1.5 mm2. When the extension

cable is on a reel, unroll the cable in its entirety.

3. OPERATION

Before setting up, repair or maintenance

of the appliance you must always turn off

the operating switch and pull out the

mains plug!

Before initial operation

• Check if the rated voltage and rated frequency

of the mains supply correspond to the details

of the type plate.

• Place the workbench on a stable and even

base.

Operation

Fig. 1

• To adjust the planing depth, turn the control

knob (1) in a clockwise direction. On the

control knob there is a pointer which shows

the planing depth in mm. Turn the control knob

until the desired planing depth is shown.

Never alter the planing depth during an

operating cycle, otherwise this will result

in an uneven surface. To prevent

operating errors turn the control knob

back to “0” when planing is completed.

• Secure the work piece with clamps or similar.

• Place the front sole on the edge of the work

piece in such a way that the planing tool does

not yet touch the work piece. The work piece

must be level.

Switching on and off

Fig. A

• Switch the machine on by pressing the On/Off

• switch (3). When you release the On/Off switch

• (3) the machine will turn off.

Lock-on Button

Fig. A

• You can lock the On/Off switch (3) by pressing

the On/Off switch (3) and then pressing the

lock-on button (4).

• To release the switch-lock; shortly press the

On/Off switch (3) again’

• The planer is now switched on and you can let

go of the release button.

• Always hold the planer with both hands on

the handles, so as to gain the best possible

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm PPM1015P Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info