Bedienungsanleitung Ferm PPM1015P (Seite 7 von 36) (Englisch, Holländisch, Französisch, Türkisch)

764213

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Warning!

• When installing and removing the plane blade,

care has to be taken that all parts (plane

blade, drum cover and screws) are clean.

Dirt or possible existing layers of dirt have to

be removed. Check regularly if the clamping

screws are tightened firmly.

Replacing the drive belt

Fig. 5

• Loosen screw (10) and take off the belt cover

(11).

• Remove worn drive belt (12).

• Before assembling a new drive belt, clean both

belt pulleys.

• Place the new drive belt on the small pulley

first and then work it on the large pulley by

hand while rotating.

• Reattach the belt cover (11) and tighten with

the screw (10).

Troubleshooting

1. The operating switch is switched on, but

the motor is not working.

• The electric circuit is broken.

• Have the electric circuit repaired.

• Wires in the mains plug or in the socket are

loose.

• Have socket and plug checked or repaired.

• The switch is faulty.

• Have the switch replaced.

2. The operating switch is switched on, but

unusual noises can be heard, the motor is

not working or only very slowly.

• Component jammed.

• Have the electric tool checked or repaired.

• Too much thrust, as a result the motor is

dragging.

• Use less thrust during the task.

3. Motor gets hot.

• Foreign substances have got inside the motor.

• Have the foreign substances removed.

• Pressure too high.

• Use less thrust during the task

• Planing tool blunt.

• Replace or sharpen the planing blade.

4. The motor is working, but the planing tool

is not moving.

• V-belt worn.

• Have V-belt replaced.

5. Frequent or strong sparks on the

commutator.

• Short circuit on the armature.

• Have the armature replaced.

• Carbon brushes worn out or jammed

• Have the carbon brushes checked.

• Rough running of the commutator.

• Have the surface of the commutator

cleaned or ground

For your own safety, never remove parts or

accessories of the electric tool during operation.

In case of fault or damage have the electric tool

repaired only by a specialist workshop or by the

manufacturer.

Use only original spare parts and original

plane blades!

Maintenance

Make sure that the plug is removed from

the mains when carrying out

maintenance work on the motor.

The machines have been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Cleaning

Regularly clean the machine housing with a

soft cloth, preferably after each use. Keep the

ventilation slots free from dust and dirt. If the dirt

does not come off use a soft cloth moistened with

soapy water. Never use solvents such as petrol,

alcohol, ammonia water, etc. These solvents may

damage the plastic parts.

Lubrication

The machine requires no additional lubrication.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm PPM1015P Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info