Bedienungsanleitung Ferm PPM1015P (Seite 6 von 36) (Englisch, Holländisch, Französisch, Türkisch)

764213

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

control over your planing operations. Besides

you do not risk becoming in touch with the

moving parts.

• When the machine has reached full speed

it can be pushed to the front over the work

piece. At the beginning of the planing

operation, put some pressure on the front

and at the end of the operation, on the rear

of the appliance. This results in the appliance

remaining flat on the work piece and prevents

the corners from getting rounded off.

• To obtain a level and smooth surface use a

greater planing depth when rough planing

and a lesser planing depth when planing a

layer. Hold the electric tool straight during the

operation, otherwise you will obtain an uneven

surface. After the operation switch off the

electric tool and remove the mains plug.

Bevelling edges

Fig. 1

The V-groove in the planer shoe allows easy

beveling of workpiece edges. Place the planer

with the V-groove (7) onto the edge of the

workpiece and guide along the edge.

Warning! Use spindle lock only in stand

still mode.

• Take care that your hand never comes in

contact with the work piece during the

operation.

• Only use the electric plane on the upper side

of the work piece, never from below or from

the side.

• Store the appliance only after it has come to a

complete standstill.

• Use a suction device to suck off wood

shavings or dust. For this use the connecting

pipe and connect a suction pipe to it.

• Use a holding device to work on small work

pieces.

Fitting the parallel guide

Fig. 4

• Loosen knob (14).

• Insert the parallel guide (10) into the slot

provided.

• Set the correct cut width and tighten the knob

(14).

4. CARE & MAINTENANCE

Before undertaking any care or

maintenance always remove the mains

plug from the socket.

The planing tool becomes worn after a period of

operation. If you use a blunt or damaged planing

tool operational efficiency is reduced and the

electric motor might become overloaded. Check

the planing tool regularly with regard to wear or

damage. Depending on its condition, the planing

tool will have to be replaced or sharpened.

Removal of plane blade

Fig. 2

Use the enclosed spanner (11). First unscrew the

three clamping screws (1) and remove the drum

cover (2) and plane blade (3), from the drum (4).

Sharpening the blades

Fig. 3a

To sharpen the blades first remove the two screws

(5) and the adjusting plate (6). Fit the planing

blades (3) into the sharpening holder (6) as

shown in the right figure and tighten the butterfly

nuts.. Use a wet sharpening stone, and keep

the holder so that both blades contact the stone

simultaneously, and sharpen the blades.

Adjusting the blades

Fig. 3b

If needed first loosely replace the adjusting plate

(6) with the two screws (5). Push the sharp edge

against the back of the adjustment tool (7), and

line up the adjusting plate (6) with the edge of the

adjustment tool (7) and tighten the screws (5).

Your plane blades are now correctly adjusted, and

can be replaced on the drum.

Installation of plane blade

Fig. 2

Take a (new) plane blade (3) and position it

between the drum cover (2) and the drum (4). With

the adjustment plate (6) in the groove of the drum

(4). Now fasten the clamping screws (5) into the

drum.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm PPM1015P Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info