Bedienungsanleitung Ferm SGM1025 (Seite 8 von 40) (Deutsch, Englisch, Holländisch, Französisch)

812760

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Vibration level

The vibration emission level stated in this

instruction manual has been measured in

accordance with astandardized test given in

EN60745; it may be used to compare one tool

with another and as apreliminary assessment of

exposure to vibration when using the tool for the

applications mentioned.

• Using the tool for different applications, or with

different or poorly maintained accessories,

may significantly increase the exposure level.

• The times when the tool is switched off or when

it is running but not actually doing the job, may

significantly reduce the exposure level.

Protect yourself against the effects of vibration by

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work

patterns.

Description

The numbers in the text refer to the diagrams on

page 2-4.

1. Nozzle nut

2. Nozzle head

3. Nozzle

4. Spray unit

5. Trigger

5a. Lock

6. Motor unit

7. Screws

8. Air filter cover

9. Air filter

10. Container

11. Riser pipe

12. Spray volume adjusting wheel

13. Cleaning brush

14. Cleaning needle

15. Measuring cup

16. Replacement air filter

17. Hanging hook

3. ASSEMBLY

Before assembly, always switch off the

machine and remove the mains plug from

the mains.

Connecting the motor unit to the spray unit

(Fig. A)

• Move the Δ mark on the spray unit (4) to the

(lock symbol) mark on the motor unit (6). Turn

the spray unit (4) until the Δ mark on the spray

unit (4) locks into the (lock symbol) mark on the

motor unit (6).

Disconnecting the motor unit and spray unit

(Fig. A)

• Unlock the lock (Fig 5a). Turn the Δ mark on

the spray unit (4) to the (lock symbol) mark on

the motor unit (6) to separate the two units.

Connecting and disconnecting the container

to the spray unit (Fig. A)

• To connect: Align the container (10) with the

spray unit (4) and insert the riser pipe (11) and

tighten.

• To disconnect: Loosen the container (10) from

the spray unit (4).

Replacing the nozzle (Fig. A)

The nozzle will be assembled on the spray gun

when taken out of the box. To replace the nozzle

follow the following steps.

• Loosen the nozzle nut (1) and remove it.

• Take out the nozzle head (2) and nozzle (3)

from the machine.

• Take the desired nozzle (3) and attach it to the

nozzle head (2).

• Place the nozzle head (2) and nozzle assembly

back in the spray unit.

• Close it by tightening the nozzle nut (1).

4. OPERATION

Preparing the spray gun for use

Step 1: Viscosity/diluting of the paint

This appliance can process spray materials up to

max. 70 DIN/sec (viscosity).

Low-viscosity coating substances, water- and

solvent based paints, finishes, primers,

2 component paint, clear finishes, staining sealers

and wood sealer preservatives often do not need

diluting.

High-viscosity Wall paints, thick varnishes and

thick stains often do need diluting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm SGM1025 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info