Bedienungsanleitung Ferm SGM1025 (Seite 9 von 40) (Deutsch, Englisch, Holländisch, Französisch)

812760

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Warning! Always use wall paint that is

smooth and without any granules or

lumps. Otherwise the nozzle will become

clogged.

Paint preparation

The appliance can process spray materials up to

amaximum of 70 DIN/s. (viscosity).

You can determine the viscosity (thickness) of the

substance with the supplied measuring cup (15)

using asimplified measuring procedure.

1. Fill the supplied measuring cup (15) to the brim

with the spray material.

2. Remove the measuring cup (15) from the spray

material and allow the liquid to run out.

3. Measure the time (in seconds) until the stream

of liquid stops. The resulting value is referred

to as DIN seconds (DIN/s).

4. If the value is too high, gradually thin the spray

material by adding small amounts of asuitable

thinning agent in and mixing the liquid.

5. Measure the DIN seconds again. Repeat this

process until you measure aviscosity of less

than 70 DIN/sec.

Tip! Most wall paints are thick and may need up

to 40% dilution.

Step 2: Preparing the spray surface

• Cover the area around the to be sprayed area

thoroughly and over awide area. Any surface

that is not covered properly can unintentionally

be sprayed.

Warning! Be aware of your surroundings

when spraying outside, wind can cause

unintentional spraying of your not

covered surroundings.

• The spray surface needs to be clean, dry, and

free from grease or dust.

• Polished surfaces should be lightly sanded,

and the sanding dust removed.

Step 3: Filling the paint container

• Remove the container (10) from the Spray unit

(4).

• Fill the container with to be sprayed material to

amaximum of 1200ml.

• Adjust the riser pipe (11) according to the

position you are going to use the spray gun in.

Spraying angle up like show in Fig. C. spraying

angle down like show in Fig. D.

• Make sure the gasket and riser pipe (11) are

properly installed in the container cap (10).

Tighten the container (11) onto the container

cap (10).

Step 4: Test and adjust the spray jet effect,

spray volume and spray flow (Fig. E)

Note: Before starting to spray the work surface,

it is advisable to make an initial test by spraying

asmall area on scrap material.

1. Choose the jet effect: Horizontally

•

Vertically

•

or Round •. By slightly undoing

the nozzle nut (1). Turn the protruding parts

of the nozzle head (2) so that they point to the

desired symbol on the spray unit (4). Than re-

tighten the union nozzle nut (1).

2. Adjust the spray volume with Spray volume

adjusting wheel (12) by turning it to the left - to

reduce the volume, to the right + to increase.

Note: Low volume is advised for smaller object

or surfaces. High volume is advised or bigger

surfaces.

Tip: We recommend starting at the minimum

setting.

3. Aim the spray gun to the to be sprayed

surface and pull the trigger (5). Hold the front

of the spray gun around 20-30 cm away from

the to be sprayed surface. Make long arm

movements rather than short wrist movements

like show in figure E. The most suitable method

of surface spraying is with across-pattern,

starting with horizontal passes and finishing

with light vertical passes. See figure F.

4. Release the trigger (5) to stop the spraying.

5. Check Spray Pattern Quality.

Agood spray pattern is evenly distributed as

it hits the surface, if not (at highest spray flow)

check the following:

- Spray tip may be worn.

- Asmaller spray tip may be needed.

- Material may need to be thinned.

6. Adjust the Jet effect (step 1), spray volume

(step 2), object- surface to be sprayed and

desired coverage. Repeat steps 3 to 5 when

not satisfied with the test results.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm SGM1025 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info