Bedienungsanleitung Ferm SGM1025 (Seite 10 von 40) (Deutsch, Englisch, Holländisch, Französisch)

812760

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Always let the paint/varnish/stains dry according

to the recommend dry time of the spray material

for applying multiple coats. Several light coats

rather than one thick coat will help prevent the

paint running.

5. MAINTENANCE

Before cleaning and maintenance, always

switch off the machine.

Cleaning after each use

It is essential that the spray gun is cleaned

thoroughly after every use. Failure to clean it will

almost certainly result in blockages and it may

not operate the next time. The guarantee does

not cover asprayer that has not been properly

cleaned by the user.

The following action must be taken after every use:

1. Empty any unused paint from the paint

container (10). Never leave paint to dry in the

unit (container, riser pipe, needle, nozzle), as

dried paint will prevent the spray gun from

functioning properly. Failure to observe this

important cautionary measure will void the

guarantee.

2. Clean the container thoroughly with the thinner

solvent you have used.

3. Put alittle thinner solvent into the container

and spray until only clean, thinner solvent exits

the spray gun.

Be aware of your surroundings when

spraying outside, wind can cause

unintentional spraying of your not

covered surroundings.

4. Clean the gasket and riser pipe (11) with

thinner solvent.

5. Clean the nozzle and remove all remaining dirt

or paint.

- Remove the nozzle nut (1), nozzle head

(2), Nozzle (3) like explained in chapter

replacing the nozzle.

- Clean all the nozzle parts thoroughly, do not

let them soak in any cleaning detergent or

water.

6. If the cylinder hole becomes blocked, use

asuitable cylinder cleaning needle.

7. Keep the ventilation slots of the device clean

to prevent the motor from overheating.

8. The ventilation slots must be free from dust

and dirt. If the dirt cannot be removed, use

asoft cloth dipped in soapy water. Never use

solvents such as benzene, alcohol, ammoniac

etc. These solvents may attack the plastic

elements.

9. The air filter (9) must be free from dust and dirt.

Ones in awhile you need to clean the air filter.

Remove the air filter like explained in chapter

“cleaning and replacing the air filter”.

10. Clean the outside of the machine. Clean

plastic parts with asoft, clean cloth, preferably

after each use.

Do not use aggressive cleansers (solvents or

abrasive cleansers), or an abrasive sponge or

sharp objects.

Do not put or immerse product in water

or any other liquid.

Always read the precautions laid down by the

paint/varnish manufacturer.

• Do not use liquids containing abrasive

substances such as red lead oxide, glazes,

caustic, and alkaline substances. The use of

these liquids can lead to excessive wear or

corrosion to the pump assembly.

Cleaning/replacing the air filter (Fig. A2)

• Loosen the screw (7) on the backside of the

machine.

• Remove the air filter cover (8) and take out the

air filter (9).

• Clean the air filter (9), always make sure it is

dry before placing it back.

• Place the dry air filter/replacing air filter back in

the motor unit (6).

• Place back the air filter cover (8) and tighten

with the screws (7).

Note: If necessary, replace the air filter (9) with the

replacement air filter (16).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm SGM1025 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info