Bedienungsanleitung Ferm TSM1031 (Seite 9 von 64) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Schwedisch, Finnisch)

510128

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

b. As a stationary machine on the subframe. In

this case the machine must be secured to the

subframe with 4 bolts and the subframe

anchored to the floor or to a floor plate with

dimensions of at least 1 square metre

Assembly of the bench saw on the workbench

Fig. B & C

Before adjusting the saw, make sure the

plug is removed from the socket.

Fig. B shows the distance of the holes to be drilled

in the workbench on which to fasten the machine.

Drill holes of 8 mm.

Only use the machine after it has been

assembled completely and it has been

screwed onto the workbench or the

frame.

• Fig. C shows the part to be sawn out (310 x

310 mm), so that the sawdust can fall through

it and piling up is prevented! Only if you do not

use an extraction system!

• Fasten the machine with bolts.

• If the frame is used, it must be fixed on the

floor with four screws and the machine must

be fixed on the frame with four screws. Check

the screws before switching the machine on.

Assemble undercarriage

Fig. G

• Turn the machine upside down.

• Remove the black plastic bottom plate by

unscrewing the 6 screws. (Fig. G-1).

• Unscrew the adjusting knob on the front and

tilt the motor (Fig. G-2), then remove the

transport packing (Fig. G-3).

• Now place one by one the uprights in the

casing of the sawing bench (Fig. G-4).

• Secure the uprights with 4 screws using a

screwdriver, do not completely tighten the

screws (Fig. G-5).

• Fit the 4 support bars, do not completely

tighten the screws (Fig. G-6)

• Fit the black plastic bottom plate and screw it

tight.

• Attach the rubber feet under the uprights (Fig.

G-7).

• Turn the machine into an upright position on a

flat surface and adjust the machine so that it

stands in a stable position, tighten all the nuts

and bolts (Fig. G-7).

Assemble bracket/push stick

• Attach the 2 brackets onto the casing of the

sawing bench and screw them tight (Fig. G-8).

• Place the push stick in the brackets.

Assembly and attachment of the rip fence

Fig. D

• Attach the aluminium fence (A) to the

positioning block (B).

• Now you can attach the complete rip fence to

the bench top.

• Slide the rip fence via one end of the

positioning rail (C) over the bench top.

• Adjust the position of the aluminium fence

profile (A) such that the end corresponds to

the rear edge of the saw.

Assembly of the riving knife and the

protective cap

Fig. E

• Turn the saw blade completely upwards.

• Remove the bench inlay.

• Assemble the riving knife on the set-up for this

purpose and use hereby the Allen screws and

the filling rings. Ensure that the riving knife

falls properly into the opening (= groove).

• Now put the inlay back in the bench and

fasten it.

• Now assembly the protective cap onto the

riving knife and use hereby the profiled nut

and self-locking nut.

Now lay a lath against the saw blade and

the riving knife and check whether it falls

properly into the extension of the saw

blade. If this is not the case: Loosen the

fastening bolts and place or remove the

filling rings.

• Above the saw table the radial distance

between the riving knife and the toothed rim of

the saw blade shall not at any point exceed 5

mm at the depth of cut set.

• The tip of the riving knife shall not be lower

than 5 mm from the tooth peak, as shown.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TSM1031 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info