Bedienungsanleitung Ferm TSM1031 (Seite 11 von 64) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Schwedisch, Finnisch)

510128

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

behind the saw blade) using a synthetic aid

instead of by hand.

Crosswise sawing

• Remove the fence and apply the cross-cut

fence in the righthand carriage.

• Adjust the height of the saw blade (see

lengthwise sawing).

• Press the workpiece against the cross-cut

fence and keep at least 2,5 cm distance from

the front of the saw blade.

• Switch on the engine and wait until the

maximum number of revolutions has been

reached.

• Press the workpiece against the fence and

the bench. Carefully push the wood through

the saw blade. Continue until behind the saw

blade. Then switch off the engine and keep

this position until the saw blade has stopped

completely before you remove the wood.

• Never pull the wood back. If necessary, switch

the engine off and keep the position until the

saw blade has stopped completely.

Crosswise sawing with a vertical mitre

This method is practically the same, except that

the saw blade is placed in the angle required.

Only place the cross-cut fence on the

righthand side of the saw blade. Never

saw too small pieces of wood. Never use

your hands to carry out difficult

operations.

Crosswise sawing with a horizontal mitre

With this method the cross-cut fence must be

secured at the angle required. Keep the

workpiece pressed firmly against the cross-cut

fence and the bench before you start cutting off.

5. Maintenance

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

These machines have been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Malfunctions

In the case that the machine is not functioning

properly, we give a number of possible causes

and appropriate solutions below.

1. Working instructions

• The plug is not in the mains.

• The cable has been interrupted.

2. The workpieces is jamming against the

riving knife during processing

• The saw blade must be aligned (Fig. E).

3. The saw cut is not smooth (frayed)

• The saw blade must be sharpened.

• The saw blade has been assembled back-to-

front.

• The saw blade has become coated with resin

or sawdust.

• The saw blade is not suitable for this process.

4. The workpiece is touching the back of the

saw blade and is jumping out

• The riving knife must be aligned (Fig. E).

• The fence is not being used.

• The saw blade is thicker than the riving knife

or the riving knife is not being used

• The saw blade must be sharpened.

• The workpiece has not been kept in its place

until after sawing.

• The tension button of the cross-cut fence is

loose.

5. The height and/or mitre handle is blocked

• Sawdust and dust must be removed.

6. The engine has difficulty reaching the

maximum number of revolutions

• The extension cable is too thin and/or too

long.

• The mains voltage is lower than 230 V.

7. The machine is vibrating

• The machine has not been fastened onto the

workbench.

• The frame is not level with the floor.

• The saw blade has been damaged.

Cleaning

Keep the ventilation slots of the machine clean to

prevent overheating of the engine. Regularly

clean the machine housing with a soft cloth,

preferably after each use. Keep the ventilation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TSM1031 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info