Bedienungsanleitung Ferm TSM1031 (Seite 10 von 64) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Schwedisch, Finnisch)

510128

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

Assembly of the saw blade

First remove the plug from the mains

before the saw blade is assembled or

replaced.

• Remove the inlay from the bench. Use a

screwdriver for this purpose.

• Turn the saw axle completely upwards.

Remove the nut and the outside flange from

the saw axle.

• Now slide the saw blade over the saw axle

and now put the outside flange and the nut

back. Tighten the nut by hand.

• Now use the 2 keys: one for the flange and

one for the nut and now clamp it.

• Now put the inlay back in the bench and

fasten it.

Mounting the push stick holders

Mount both push stick holders on the side of the

machine using the bolts and rings supplied.

Use of the mitring set-up

Fig. A

By turning the handle at the side of the machine

you can adjust the saw blade to a maximum of 45°

(4).

4. Operation

Working instructions

There are two types of sawing methods:

• Lengthwise sawing

Sawing the workpiece in the length of

the wood grain.

• Cross-cutting or cutting off

Sawing off the workpiece crosswise.

If it concerns a panel, we do not usually

distinguish between the wood grain, but we name

the method where we saw off a part of the width of

the panel (lengthwise sawing) and when we cut

off the length (cross-cutting or cutting-off).

For both sawing methods one of the

fences must be used. Therefor never

saw without a fence!

Attention! Before you start sawing, first check the

following:

1. Is the saw blade secured?

2. Are all the locking handles secured?

3. Is the fence parallel to the saw blade?

4. Is the protective cap working properly?

5. Are you wearing safety goggles?

6. Is the saw blade not rubbing against

anything?

It is absolutely necessary to take these

points into consideration before you

start work!

Lengthwise sawing

• Secure the fence to the correct measuring

position and remove the cut-off guide from the

bench carriage.

• Turn the saw blade approximately 2 mm

higher than the total thickness of the wood to

be sawn.

• Press the wood lightly towards the bench and

let it glide against the cut-off fence.

Remain at least 3 cm. from the front of

the saw blade before you switch on the

engine. The side of the wood which is

against the fence must be completely

straight. Keep your hands at least 10 cm

away from the saw track to be followed.

• Switch on the engine and wait until the saw

blade has reached the maximum number of

revolutions before you start sawing.

• While you press the wood against the bench

and the fence, you can carefully push the

wood through the saw blade without forcing it.

• Never pull the workpiece backwards. If

necessary, switch off the engine first without

altering the position of the workpiece.

Lengthwise sawing with a (vertical) mitre

This method is practically the same, except that

the saw blade is placed at the angle required.

With this type of method the fence may

only be along the righthand side of the

sawblade.

Lengthwise sawing of narrow workpieces

Assume that this process is extremely

dangerous.

Take all the necessary safety measures and

continually push the workpiece through (until

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TSM1031 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info