Bedienungsanleitung Ferm TSM1033 (Seite 9 von 112) (Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

634180

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

38. Do not use saw blades which are damaged or

deformed.

39. Replace table insert when worn.

40. Only use saw blades specified by the

manufacturer that are intended for working

with wood or similar materials according to

EN847-1.

41. Take care that the selection of the saw blade

depends on the material to be cut.

42. Connect tabelsaws to a dust-collecting device

when sawing.

43. Use and correct adjustment of the riving knife

44. Use and correct adjustment of the upper saw

blade quard.

45. Take care when slotting.

Make sure, when changing the saw blade, the

blade width is not smaller and the main blade

thickness of the saw blade is not greater than the

thickness of the riving knife.

Wear personal protective equipment, these could

include:

• Hearing protection to reduce the risk of

hearing loss

• Eye protection

• Inhale respiratory protection to reduce the risk

of harmful dust

• Gloves when handling the blades and rough

materials (recommendation, saw blades, are

whenever practicable, carried in a container)

Warning! Do not use HSS blades.

• Insert the push stick in its holder when not in

use.

• Use a push stick or a push block to guide the

workpiece.

Warning! Do not use the saw for rebating

or grooving.

• Only use saw blades, whose maximum speed

is at least the speed indicated on the saw and

is suitable for the material to be cut.

• During the transport, the upper part of the saw

blade has to be covered, by the guard.

Switch off the machine immediately when you

discover:

• A defective mains plug or mains lead.

• A defective switch.

• Overheating of the machine.

• Smoke or odeur caused by scorched

insulation.

Electrical safety

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Always check that the power supply

corresponds to the voltage on the rating

plate.

Replacing cables or plugs

Immediately throw away old cables or plugs

when they have been replaced by new ones. It is

dangerous to insert the plug of a loose cable in

the wall outlet.

Using extension cables

• As a supply for this machine always use an

unloaded line and/or an extension cable with

conductors of at least 1,5 mm

and protected

with a 16 A fuse. Be sure that this extension

cable is not longer than 20 metres.

• This machine can be switched to the single-

phase network (230-240 V/50 Hz). If you are

in doubt about the earth of the electricity

provisions, consult an electrician first.

Power supply

• The motor is fitted with an overload switch (8).

If the table saw overloads, the overload switch

switches the equipment off automatically to

protect the table saw from overheating. If the

overload switch triggers, switch off the table

saw using the ON/OFF switch (7) and wait

until the table saw cools down. Then press the

overload switch (8) and restart the table saw.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TSM1033 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ferm TSM1033

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info