Bedienungsanleitung Ferm TSM1033 (Seite 11 von 112) (Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

634180

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

Assembly of the saw blade

Fig. K

First remove the plug from the mains

before the saw blade is assembled or

replaced.

The arrow marked on the saw blade,

which indicates the direction of rotation.

Must point in the same direction as the

arrow marked on the machine, the saw

blade teeth must point downwards on

the front of the saw.

• Remove the inlay from the bench. Use a

screwdriver for this purpose.

• Turn the saw axle completely upwards (Fig.A, 5).

Remove the nut and the outside flange from the

saw axle (Fig. K, direction A).

• Now slide the saw blade over the saw axle and

now put the outside flange and the nut back.

Tighten the nut by hand.

• Now use the 2 keys: one for the flange and one

for the nut and now clamp it (Fig. K, direction B).

•

Now put the inlay back in the bench and fasten it.

Use of the mitring set-up

Fig. A

By turning the handle (4) at the front of the machine

you can adjust the saw blade to a maximum of 45°.

4. OPERATION

Switching On/Off

Fig. A (7)

• Press the switch into position ‘1’ to put your

machine into operation.

• To switch off the machine the same switch

needs to be pressed to position ‘0’.

• Always keep the mains cable away from

moving parts.

Using the height handle

Fig. A

• Turn height handle (5) clockwise to raise the

sawblade

• Turn height handle counterclockwise to lower

the sawblade

• Turn the saw blade approximately 2 mm higher

than the total thickness of the wood to be sawn.

Using mitre handle

Fig. A

• Release mitre handle (4) by turning the outer

part counter clockwise

• Use mitre handle to set the right mitre angle for

your cut by turning the inner part

• mitre handle by turning the outer part

clockwise.

Working instructions

There are two types of sawing methods:

• Lengthwise sawing

Sawing the workpiece in the length of the

wood grain.

• Cross-cutting or cutting off

Sawing off the workpiece crosswise.

If it concerns a panel, we do not usually

distinguish between the wood grain, but we name

the method where we saw off a part of the width

of the panel (lengthwise sawing) and when we cut

off the length (cross-cutting or cutting-off).

For both sawing methods one of the

fences must be used. Therefor never saw

without a fence!

Attention! Before you start sawing, first check the

following:

1. Is the saw blade secured?

2. Are all the locking handles secured?

3. Is the fence parallel to the saw blade?

4. Is the protective cap working properly?

5. Are you wearing safety goggles?

6. Is the saw blade not rubbing against anything?

It is absolutely necessary to take these

points into consideration before you start

work!

Lengthwise sawing

• Secure the fence to the correct measuring

position and remove the cut-off guide from the

bench carriage. (Fig. J)

• Turn the saw blade approximately 2 mm higher

than the total thickness of the wood to be

sawn.

• Press the wood lightly towards the bench and

let it glide against the cut-off fence.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TSM1033 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ferm TSM1033

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info