Bedienungsanleitung Ferm TSM1033 (Seite 12 von 112) (Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

634180

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

Remain at least 3 cm. from the front of

the saw blade before you switch on the

motor. The side of the wood which is

against the fence must be completely

straight. Keep your hands at least 10 cm

away from the saw track to be followed.

• Switch on the motor and wait until the saw

blade has reached the maximum number of

revolutions before you start sawing.

• While you press the wood against the bench

and the fence, you can carefully push the

wood through the saw blade without forcing it.

• Never pull the workpiece backwards. If

necessary, switch off the motor first without

altering the position of the workpiece.

Lengthwise sawing with a (vertical) mitre

This method is practically the same, except that

the saw blade is placed at the angle required.

With this type of method the fence may

only be along the righthand side of the

sawblade.

Lengthwise sawing of narrow workpieces

Assume that this process is extremely

dangerous.

Take all the necessary safety measures and

continually push the workpiece through (until

behind the saw blade) using a push stick instead

of by hand.

Crosswise sawing

• Remove the fence and apply the cross-cut

fence in the righthand carriage.

• Adjust the height of the saw blade (see

lengthwise sawing).

• Press the workpiece against the cross-cut

fence and keep at least 2,5 cm distance from

the front of the saw blade.

• Switch on the motor and wait until the maxi-

mum number of revolutions has been reached.

• Press the workpiece against the fence and

the bench. Carefully push the wood through

the saw blade. Continue until behind the saw

blade. Then switch off the motor and keep

this position until the saw blade has stopped

completely before you remove the wood.

• Never pull the wood back. If necessary, switch

the motor off and keep the position until the

saw blade has stopped completely.

Crosswise sawing with a vertical mitre

This method is practically the same, except that

the saw blade is placed in the angle required.

Only place the cross-cut fence on the

righthand side of the saw blade. Never

saw too small pieces of wood. Never use

your hands to carry out difficult operations.

Crosswise sawing with a horizontal mitre

With this method the cross-cut fence must

be secured at the angle required. Keep the

workpiece pressed firmly against the cross-cut

fence and the bench before you start cutting off.

5. MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

These machines have been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Transporting the bench saw

Before transporting the bench saw, the following

steps must be carried out:

• Pull the mains plug

• Turn the hand-wheel 5 (Fig. A) in anticlockwise

direction, lower the blade as much as possible

• Remove all accessories that cannot be

mounted firmly to the power tool

If possible, place unused saw blades in an

enclosed container for transport

• Slide the saw-table extension 9 completely

inward and turn the knob (Fig F-3) to lock it

• Wind the mains cable and bind it

• For lifting or transport, carry the main table 2

(Fig.A)

The bench saw should always be carried by

two persons in order to avoid back injuries.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TSM1033 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ferm TSM1033

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info