Bedienungsanleitung Ferm TSM1033 (Seite 10 von 112) (Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

634180

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

3. ASSEMBLY INSTRUCTIONS

Assembly of the table extensions

Fig. F

• Assemble table extensions (2pcs) like shown

on Fig.F1

• Tighten the screws (4pcs) like shown on Fig.F2

• Use knobs (4pcs) to tighten the table

extensions Fig.F3

Assembly of the dust extraction

Fig. I

• Assemble dust extraction like shown on Fig.I

• Attach vacuum cleaner to A (Fig.I)

Installation of the machine on a workbench or

on the subframe

This machine is a stationary machine and for

safety reasons must always be firmly installed and

not used for mobile applications.

You can install the machine in two ways:

a. As a stationary machine on a workbench. In

this case the machine must be secured to the

workbench with 4 bolts.

b. As a stationary machine on the subframe. In

this case the machine must be secured to

the subframe with 4 bolts and the subframe

anchored to the floor or to a floor plate with

dimensions of at least 1 square metre

Assembly of the bench saw on the workbench

Fig. B & C

Before adjusting the saw, make sure the

plug is removed from the socket.

Fig. B shows the distance of the holes to be

drilled in the workbench on which to fasten the

machine. Drill holes of 8 mm.

Only use the machine after it has been

assembled completely and it has been

screwed onto the workbench or the

frame.

• Fig. C shows the part to be sawn out (310 x

310 mm), so that the sawdust can fall through

it and piling up is prevented! Only if you do not

use an extraction system!

• Fasten the machine with bolts.

• If the frame is used it must be fixed to the floor

with at least 2 screws on the front legs (Fig.H)

Assemble undercarriage

Fig. G

• 1: Create the square by using beams from D

using bolts and nuts supplied (type 1) , make

sure beams D1 (2pcs) are placed over D2 (Fig.

G1, and Fig.G2) do not tighten the bolts yet

• 2: Mount beams B on the machine using bolts

type 2, make sure they are mounted on the

sides of the table extensions (Fig.G3)

• 3: Mount legs A on the machine like on Fig.G4

and use 2 bolts (type 1) per leg to tighten

• 4: Mount the square in between the legs, make

sure the D2 beams are on the side of the table

extensions

• 5: Make sure the square is fixed well, and

tighten the nuts and bolts well (Fig.G5)

• 6: Place rubber feet (Fig.G6)

• 7: Tighten the nuts and bolts from step 1

• 8: Mount 2 sliding feet (Fig.G7)

Assembly and attachment of the parallel guide

Fig. D

• Attach the aluminium guide (A) to the

positioning block (B).

• Now you can attach the complete parallel

guide to the bench top.

• Slide the parallel guide via one end of the

positioning rail (C) over the bench top.

• Adjust the position of the aluminium guide

profile (A) such that the end corresponds to the

rear edge of the saw.

Assembly of the riving knife and the protective cap

Fig. E

• Turn sawblade completely upwards (Fig.A,

number 5)

• Assemble the guard (Fig.E1 & Fig.E2)

• Above the saw table the radial distance

between the riving knife and the toothed rim of

the saw blade shall not at any point exceed 5

mm at the depth of cut set.

• The tip of the riving knife shall not be lower

than 5 mm from the tooth peak, as shown in

Fig.E3.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TSM1033 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ferm TSM1033

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info