Bedienungsanleitung Ferm TSM1033 (Seite 13 von 112) (Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

634180

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

Malfunctions

In the case that the machine is not functioning

properly, we give a number of possible causes

and appropriate solutions below.

1. The motor does not start

• The plug is not in the mains.

• The cable has been interrupted.

• The carbon brushes are worn out. Replace the

carbon brushes or consult your dealer.

2. The workpieces is jamming against the

riving knife during processing

• The saw blade must be aligned (Fig. E).

3. The saw cut is not smooth (frayed)

• The saw blade must be sharpened.

• The saw blade has been assembled back-to-

front.

• The saw blade has become coated with resin

or sawdust.

• The saw blade is not suitable for this process.

4. The workpiece is touching the back of the

saw blade and is jumping out

• The riving knife must be aligned (Fig. E).

• The fence is not being used.

• The saw blade is thicker than the riving knife or

the riving knife is not being used

• The saw blade must be sharpened.

• The workpiece has not been kept in its place

until after sawing.

• The tension button of the cross-cut fence is

loose.

5. The height and/or mitre handle is blocked

• Sawdust and dust must be removed.

6. The motor has difficulty reaching the

maximum number of revolutions

• The extension cable is too thin and/or too long.

• The mains voltage is lower than 230-240 V.

7. The machine is vibrating

• The machine has not been fastened onto the

workbench.

• The frame is not level with the floor.

• The saw blade has been damaged.

8. The electromotor runs unevenly

• The carbon brushes are worn out. Replace the

carbon brushes or consult your dealer.

Cleaning

Keep the ventilation slots of the machine clean to

prevent overheating of the motor. Regularly clean

the machine housing with a soft cloth, preferably

after each use. Keep the ventilation slots free from

dust and dirt. If the dirt does not come off use a

soft cloth moistened with soapy water. Never use

solvents such as petrol, alcohol, ammonia water,

etc. These solvents may damage the plastic parts.

Lubrication

The machine requires no additional lubrication.

Faults

Should a fault occur, e.g. after wear of a part,

please contact your local Ferm dealer. In the back

of this manual you find an exploded view showing

the parts that can be ordered.

ENVIRONMENT

To prevent damage during transport, the

appliance is delivered in a solid packaging which

consists largely of reusable material. Therefore

please make use of options for recycling the

packaging.

Damaged and/or disposed of electrical or

electronic devices must be dropped off

at recycling stations intended for that

purpose.

Only for EC countries

Do not dispose of power tools into domestic

waste. According to the European Guideline

2012/19/EU for Waste Electrical and Electronic

Equipment and its implementation into national

right, power tools that are no longer usable must

be collected separately and disposed of in an

environmentally friendly way.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TSM1033 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Ferm TSM1033

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info