Bedienungsanleitung Ferm TSM1036 (Seite 10 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

764020

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

1. Remove the saw blade cover (31) by loosening

the Phillips screws (32).

2. Loosen the nut by attaching the large spanner

(29) to the nut and using the small spanner

(30) on the motor shaft in order to counteract.

Attention: turn the nut in the direction of

rotation of the saw blade.

3. Remove the outer flange and remove the saw

blade (4).

4. Carefully clean the saw blade flanges before

installing the new saw blade. Replace and

tighten the new saw blade in reverse order.

The arrow marked on the saw blade,

which indicates the direction of rotation,

must point in the same direction as the

arrow marked on the machine, the saw

blade teeth must point downwards on

the front of the saw.

• Before you start working with the saw again,

the functionality of the protective devices must

be checked.

•

Warning! After each saw blade change, check

that the saw blade guard (2) opens and closes

as required. Additionally check whether the saw

blade (4) runs freely in the saw blade guard (2).

• Warning! After each saw blade change, check

that the saw blade (4) can move freely in the

table insert (6), when in vertical position and

when tilted to 45°.

Fixing on a substructure

Fig. A

The mounting holes (20) on the machine frame

are used to attach the device on a solid, flat base

such as on a workbench. Matching mounting

material (screws, etc.) are available at specialist

stores.

Dust Extraction

Fig. I

The saw is equipped with a dust extraction

system.

• Insert the vacuum cleaner adapter (16) in the

dust extraction port (25).

• It is strongly advised to use a dust extraction

system that is suitable for the material

wherever possible.

• Regularly check and clean the suction

channels.

Storage of loose parts

Fig. A, I

When not in use, the push stick (3), Parallel guide

(7) and Mitre guide (14) can be attached. The push

stick (3) can be stored in the machine housing,

as shown on figure A. The Mitre guide(14) can be

fixed to the machine housing with the wing nut

(36) as shown in figure I.

4. OPERATION

Switching on/off

Fig A

• Press the switch into position ‘1’ to put your

machine into operation.

• To switch off the machine the same switch

needs to be pressed to position ‘0’

• Always keep the mains cable away from

moving parts.

Parallel guide

Fig. A, J, K

When slitting wood parts, the Parallel guide (7)

must be used.

• Mount the Parallel guide (7) on the table

surface (1) with the clamping plate (26);

Washers (27) and knobs (12): Outside of the

saw table: set screw (12) and washer (27);

Inside of the saw table: clamping plate (26).

User modes

The supplied Parallel guide (7) has two different

height guide surfaces, one on each side of

the guide. Use the lower height side for flat

workpieces, the higher stop height for tall

workpieces.

1. To change the height of the stop, open the

knobs (12) on the Parallel guide (7) and remove

it from the table.

2. Turn the Parallel guide (7) 180 ° so that the front

end points to the rear.

3. Tighten the knobs (12) again.

Cutting width

The Parallel guide (7) can be mounted on both

sides of the table surface (1).

1. Loosen the two knobs (12).

2. With the aid of the ruler (22) on the table surface

(1), the Parallel guide (7) can be adjusted to the

desired size.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TSM1036 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info