Bedienungsanleitung Ferm TSM1036 (Seite 9 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

764020

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

4. Saw blade

5. Riving knife

6. Table insert

7. Parallel guide

8. Front knob for angle adjustment

9. Rear knob for angle adjustment

10. Angle scale

11. On / Off switch

12. Knob for parallel guide

13. Angle scale indicator

14. Mitre guide

15. Nut for saw blade

16. Vacuum cleaner adapter

17. Countersunk screw

18. L-shaped recess in the riving knife

19. Fixing screw

20. Mounting holes

21. Groove in table surface

22. Ruler

23. Extension for mitre guide

24. Knobs for mitre guide

25. Dust extraction port

26. Clamping plate for parallel guide

27. Washer for parallel guide

28. Knob for mitre angle

29. Large spanner

30. Small spanner

31. Saw blade cover

32. Phillips screw for saw blade cover

33. Knob for guard

34. Nut for guard

35. Carriage bolt for guard

36. Wing nut

3. ASSEMBLY

Before carrying out any work on the

machine, disconnect the mains plug

from the power supply.

Installing / removing saw blade guard

Fig. A, B, C

1. Open the knob (33) as far as possible until the

knob (33) touches the nut (34), as shown on

figure B. Attention: do not adjust the nut (34).

2. Push the carriage bolt (35) as far as possible

through the saw blade guard (2) so that

the square profile of the carriage bolt (35)

protrudes from the saw blade guard (2).

3. Mount the saw blade guard (2) with the

carriage bolt (35) into the L-shaped recess (18)

of the Riving knife (5): first forward and then

down, as shown on figure C.

4. Then push the carriage bolt (35) back again,

with the square profile into the recess in the

saw blade guard (2).

5. Tighten the knob (33) as far as possible.

Attention: the upper saw blade guard must be

able to move freely. Disassembly is carried out

in reverse order.

Replacing the table insert

Fig. D

A worn or damaged table insert (6) must

be replaced immediately.

In the event of wear or damage, the table insert

must be replaced. Otherwise there is an increased

risk of injury.

1. Remove the saw blade guard (2) as explained

in aforementioned paragraph.

2. Loosen the countersunk screws (17).

3. Replace table insert (6). The new table insert is

installed in reverse order.

Adjusting the Riving knife

Fig. E, F

1. Remove the saw blade guard (2) as explained

in aforementioned paragraph.

2. Loosen the screws (19) and remove the riving

knife (5). The distance between saw blade

(4) and Riving knife (5) should be 3-8 mm, as

shown on figure F.

3. Ensure the riving knife is straight and centered

behind the saw blade (4).

Mounting / changing the saw blade

Fig. G, H

When mounting the saw blade, wear

protective gloves. Danger of injury when

touching the saw blade.

Only use saw blades that correspond

with the characteristic data given in the

operating instructions. Use only saw

blades that are marked with a speed

equal or higher than the speed marked

on the machine.

Do not under any circumstances use

grinding discs as the cutting tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TSM1036 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info