Bedienungsanleitung Ferm TSM1036 (Seite 11 von 136) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

764020

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

3. Tighten the two knobs (12) to fix the Parallel

guide (7).

4. In addition to the scale display, measure the

cutting width between saw blade and Parallel

guide. After a new setting, make a test cut to

check the dimensions.

Mitre guide

Fig. L

For cross-cutting of wooden parts, the Mitre

guide(14) must be used.

1. Fix the Mitre guide extension (23) to the Mitre

guide (14) with the knobs for mitre guide (24).

2. Push the Mitre guide(14) into the groove (21) of

the table surface.

3. Loosen the knob for mitre angle (28).

4. Turn the Mitre guide extension (23) until the

arrow points to the desired angle.

5. Tighten the knob for mitre angle (28) again.

6. Check the distance between Mitre guide

extension (23) and saw blade (4).

Warning! Do not push the Mitre guide extension

(23) too far towards the saw blade. The distance

between Mitre guide extension (23) and saw blade

(4) should be approx. 2 cm. If necessary, loosen

the two knobs for mitre guide (24) and adjust the

Mitre guide extension (23). Afterwards, retighten the

knobs for mitre guide (24).

Angle adjustment

Fig. A, I

1. Loosen both the front knob for angle adjustment

(8) and the rear knob for angle adjustment (9).

2. Adjust the saw blade angle by sliding the two

knobs (8, 9) until the indicator (13) matches the

desired angle on the angle scale (10).

3. Tighten both the front knob for angle adjustment

(8) and the rear knob for angle

adjustment (9).

Working instructions

There are two types of sawing methods:

• Lengthwise sawing (Fig.K)

Sawing the workpiece in the length of the

wood grain

• Cross-cutting or cutting off, use the mitre

guide (Fig.L)

Sawing off the workpiece crosswise

For both sawing methods one of the

fences must be used. Therefor never saw

without a fence!

Attention! Before you start sawing, first check the

following:

1. Is the saw blade secured?

2. Are all the locking handles secured?

3. Is the fence parallel to the saw blade?

4. Is the protective cap working properly?

5. Are you wearing safety goggles?

6. Is the saw blade not rubbing against anything?

It is absolutely necessary to take these

points into consideration before you start

work!

Lengthwise sawing

• Secure the fence to the correct measuring

position and remove the cut-off guide from the

bench carriage.

• Press the wood lightly towards the bench and

let it glide against the cut-off fence.

Remain at least 3 cm. from the front of

the saw blade before you switch on the

motor. The side of the wood which is

against the fence must be completely

straight. Keep your hands at least 10 cm

away from the saw track to be followed.

• Switch on the motor and wait until the saw

blade has reached the maximum number of

revolutions before you start sawing.

• While you press the wood against the bench

and the fence, you can carefully push the

wood through the saw blade without forcing it.

• Never pull the workpiece backwards. If

necessary, switch off the motor first without

altering the position of the workpiece.

Lengthwise sawing with a (vertical) mitre

This method is practically the same, except that

the saw blade is placed at the angle required.

With this type of method the fence may

only be along the righthand side of the

sawblade.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ferm TSM1036 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info