Bedienungsanleitung Festool CS 50 EB (Seite 18 von 110) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

498001

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

3.4 Residual risks

In spite of compliance with all relevant design

regulations, dangers may still present them-

selves when the machine is operated, e.g.:

- Workpiece parts being thrown off,

- Parts of damaged tools being thrown off,

- Noise emission,

- Sawdust emission.

4 Setting up, commissioning

Ensure that the ﬂ oor around the machine is level,

in good condition and free of loose objects (e.g.

chips and offcuts).

4.1 Mounting the machine

The machine can be set up with or without the

legs folded out (Fig. 1 and 2) (the „Floor“ model

does not include folding legs).

To fold out the legs, open the four rotary knobs

(1.6) as far as they will go. After folding out the

legs, retighten the four rotary knobs.

So that the machine stands securely, the length

of one of the legs can be changed by turning the

cap on the end (1.7).

4.2 Transport

- Engage the saw unit in the zero position.

- Remove all attachments from your saw and wind

up the cable on the cable holder.

- Fold up the legs.

4.3 Applications

The machine can be used as a bench-mounted

circular saw or as a circular trimming saw.

a) Bench-mounted circular saw (Fig. 1)

- Set the switch (1.9) to the lower position.

- Swing the hand grip (1.8) downwards, and use

the hand grip to pull the saw unit forwards until

it locks into place.

The saw unit is now in a central bench position

and the machine can be used as a bench-mounted

circular saw.

b) Circular trimming saw (Fig. 3)

- Set the switch (3.10) to the upper position.

If the hand grip (3.9) is swung downwards, it can

be used to move the saw unit backwards and for-

wards for drawing cuts. The backward movement

is supported by spring force.

4.4 Dust extraction

The PRECISIO has two extraction con-

nections: the upper protective cover (2.3)

with a diameter of 27 mm, and the lower

protective cover (2.2) with a diameter of

35 mm.

The extraction set CS 70 AB (488292, included in

scope of delivery for CS 50 EB) joins both of the

extraction connections so that a Festool extractor

module can be connected.

4.5 Power supply and start-up

The mains voltage must correspond to

the speciﬁ cation on the rating plate.

In North America, only Festool machines

with the voltage speciﬁ cations 120 V/60

Hz may be used.

On account of the performance capability of the

motor, we recommend a 16 A fuse.

To switch on, press the ON/OFF switch (4.1) and

the locking switch (4.4) simultaneously. The

machine runs as long as the ON/OFF switch is

pressed.

For continuous operation after switching on, ﬁ rst

press the ON/OFF switch (4.1) and then let go of

the locking switch (4.4). To switch off continuous

operation, either press the ON/OFF switch again

and let it go or press the red switch (4.6). To protect

against unauthorised activation, a shackle type

connector can be inserted in the hole (4.2) of the

ON/OFF switch.

5 Electronics

The machine has full-wave electronics

with the following features:

5.1 Smooth start-up

The smooth start-up ensures the machine starts

up jolt-free.

5.2 Speed adjustment

You can regulate the speed steplessly between

1600 and 4200 rpm using the adjusting wheel (4.5).

This enables you to optimise the cutting speed to

suit the material (4.3).

The pre-selected speed remains constant whether

the machine is in operation or in neutral posi-

tion.

5.3 Overload protection

In the event of an extreme overload of the ma-

chine, the power supply is reduced. If the motor

is blocked for a longer period, the power supply

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool CS 50 EB Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info