Bedienungsanleitung Festool CS 50 EB (Seite 19 von 110) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

498001

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

is interrupted completely. After removal of the

blockage or switching on again, the machine is

operational once again.

5.4 Temperature protection

If the motor temperature becomes too high, the

power supply and speed are reduced. The ma-

chine then only runs with reduced power to enable

rapid cooling by means of the motor ventilation.

After cooling down, the machine accelerates again

automatically.

5.5 Brake

After switching-off the tool, the saw blade is elec-

tronically brought to a standstill in 1.5 – 2 seconds

(only for 230 V - 240 V conﬁ guration).

5.6 Restart protection

The built-in undervoltage release prevents that

the machine restarts on its own in the continu-

ous operation mode following a power cut. In this

case, the machine must ﬁ rst be switched off and

then on again.

6 Machine settings

Prior to any setting, maintenance or re-

pair, pull the mains plug!

To make setting easier, the saw unit can be locked

in the front position (Fig. 5): pull the saw unit

forwards as far as it will go and place the switch

(5.1) in the lower position.

The machine must not be used in the front

position!

6.1 Cutting depth

The cutting depth can be set steplessly (0 - 50 mm

with 90° position of the saw blade) by turning the

crank handle (5.4).

6.2 Mitre

The saw blade can be pivoted between 0° and

45°:

- Open the rotary knob (5.3).

- Set the mitre using the scale (5.6) by turning the

handle (5.2).

- Close the rotary knob (5.3).

For exact ﬁ tting work (relief cutting on the bor-

dering), the saw blade can be pivoted 2° beyond

the two end positions. To do so, the button (5.5)

is pressed in the end position; the saw blade can

then be pivoted up to -2° or 47°. On pivoting back,

both end positions are active once again.

6.3 Changing tools

Safety Instructions Fast-Fix Tension Nut

(see Fig. 7 A).

After tensioning, close the handle bow.

Only tighten or loosen the Fast-Fix Tension

Nut by hand. Under no circumstances use

the handle bow with aid of screwdrivers,

pliers, or other tools for tightening or

loosening.

If the nut cannot be loosened by hand, only

use a pin-type face spanner for support.

Never continue to use the Fast-Fix nut,

in case the handle bow is loose or dam-

aged.

Due to the special shank, only the saw

blades offered by Festool for this machine

may be used.

- Open the locking mechanism (1.3) and remove

the bench insert (1.2) upwards

- Open the locking mechanism (6.1) and swing the

saw blade cover (6.2) down. This automatically

locks the tool spindle

- Shift the lever (7.5) and turn clockwise (left-hand

thread) to open the Fast-Fix clamp (7.4)

- Change the tool. In doing so, bear in mind:

• The Fast-Fix clamp (7.4), ﬂ ange (8.1) and saw

blade must be clean

• The direction of rotation on the saw blade (7.6)

must match the direction of rotation of the

machine (7.7)

• Place the saw blade on the centre of the ﬂ ange

(8.1) and turn until the contour of the ﬂ ange

and the saw blade hole lock.

- Firmly tighten the Fast-Fix clamp (7.4) anticlock-

wise; shift the lever (7.5)

- Swing the saw blade cover (6.2) upwards and

close the locking mechanism (6.1)

- Insert the bench insert with the rear edge ﬁ rst

(see Fig. 9) and close the locking mechanism

(1.3).

6.4 Setting the riving knife

The spacer wedge (7.1) is to be set in such a way

that the gap to the chuck of the saw blade is 3 to

5 mm.

- Use the Allen key (6.3) to remove the screw (7.3)

and take it out together with the clamping ele-

ment (7.2),

- After both of the screws (8.3) have been opened,

the guide element (8.2) can be shifted vertically

to set the gap between the spacer wedge and

saw blade.

- After completion of the setting, ﬁ t the spacer

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool CS 50 EB Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info