Bedienungsanleitung Festool CS 50 EB (Seite 20 von 110) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

498001

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

wedge and clamping element again and tighten

all screws.

6.5 Guide

As shown in Fig. 3, the supplied guide can be se-

cured to all four sides of the machine. The guide

offers the following adjustment options:

• Adjustment parallel to the bench edge - open

the rotary knob (3.5).

• Adjustment vertical to the bench edge - open

the rotary knob (3.6).

• Adjustment of the sliding fence (3.1) in a longitu-

dinal direction - open the rotary knob (3.2). The

sliding fence can be clamped onto the holder in

a low position for thin workpieces (Fig. 1), or in

a high position for thick workpieces (Fig. 3).

• Angle adjustment using the scale (3.7) - open

the rotary knob (3.3) and raise the ﬁ xing pin

(3.4). The rotating ﬁ xing pin locks into place in

the most common angle positions.

This means that the guide can be used as a par-

allel guide (Fig. 1) or as a cross guide or angle

guide (Fig. 3).

Prior to all work, make sure that all rotary

knobs of the guide are tightened. The

guide may only be used in a ﬁ xed position

and not to shift the workpiece.

6.6 Scale for cutting width

The two scales (1.5) specify the cutting width for

longitudinal cuts.

If required, the scales can be realigned after open-

ing the screws (1.4).

6.7 Mounting the splinterguard

The splinterguard (10.2) prevents breakouts on

the lower cutting edge of the workpiece.

The splinterguard can be used for all mitres, but

a separate splinterguard must be ﬁ tted and sawn

in for each angle:

- Set saw blade to minimum cutting depth.

- Open the locking mechanism (1.3) and remove

the bench insert (1.2) upwards.

- Open the locking mechanism (6.1) and swing the

saw blade cover (6.2) down. This automatically

locks the tool spindle.

- Push splinterguard (10.2) from the side into the

holder (10.3) up to the stop.

- Swing the saw blade cover (6.2) upwards and

close the locking mechanism (6.1).

- Insert the bench insert with the rear edge ﬁ rst

(see Fig. 9) and close the locking mechanism

(1.3).

- Switch on tool and slowly move the saw blade

up to the maximum cutting depth – this cuts the

splinterguard to shape.

For a optimum function the raised part (10.1) of

the splinterguard should protrude slightly (approx.

0.3 mm) above the surface of the base runner. For

this purpose the height of the holder (10.3) can be

adjusted after releasing both screws (10.4).

7 Working with the machine

When working with the machine, comply

with all safety instructions.

Adjust the protective hood so that it rests on the

workpiece and clamp it in this position with the

knob (1.1).

7.1 Bench-mounted circular saw

Use the guide as a parallel guide (Fig. 1) to guide

the workpiece. The cutting width can be set using

the scales (1.5). Guide the workpiece into place by

hand. Use the workpiece holder (2.4) to guide the

workpiece safety past the saw blade. When not in

use, place the work-piece holder in the storage

compartment (2.1).

7.2 Circular trimming saw

Use the guide as a cross guide or as an angle

guide (Fig. 3) to apply and secure the work-piece.

Alternatively, clamps (489570) can be inserted in

the grooves (3.8) to secure the workpiece. Perform

the sawing cut by swinging the hand grip (3.9)

downwards and using the hand grip to pull the

saw unit forwards. After making the sawing cut,

move the saw unit right back again into its initial

position before you take the workpiece from the

guide.

8 Maintenance and care

Prior to any setting, maintenance or re-

pair, pull the mains plug!

All maintenance and repair work which

requires the motor casing to be opened

may only be carried out by an authorised

service centre.

Damaged safety devices and parts should

be repaired or replaced by an authorised

service centre unless otherwise speciﬁ ed

in the operating instructions.

The routers are ﬁ tted with special carbon brushes

with automatic-switch-off. When the brushes

reach their wear limit the current is interrupted

automatically and the router comes to a stand-

still.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool CS 50 EB Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info