510172
14
Zoom out
Zoom in
Vorherige Seite
1/100
Nächste Seite
14
DF 700 EQ
GB
when under load.
Temperature cut-out
The machine power supply is limited and the speed
reduced if the motor exceeds a certain tempera-
ture. The machine continues operating at reduced
power to allow the ventilator to cool the motor
quickly. If the machine temperature exceeds the
maximum permitted value for longer periods, the
machine switches off completely after approx. 40
seconds and can only be switched on again once the
motor has cooled sufficiently.
Restart protection
The integral restart protection prevents the ma-
chine from automatically starting up again after an
interruption in power when the machine is used in
continuous operating mode. In this case the ma-
chine must be switched off and then switched back
on again.
7.2 Changing tools
Removing the tool
Lift the unlocking device
[3-2]
until it audibly
disengages using the open-ended spanner
[3-
3]
supplied (SW 12).
Separate the motor unit
[3-5]
from the guide
frame
[3-4]
.
Press and hold the spindle lock
[4-1]
.
Loosen the cutter
[4-3]
using the open-ended
spanner
[4-2]
and remove.
Release the spindle lock
[4-1]
.
Inserting the tool
Press and hold the spindle lock
[4-1]
.
Use the open-ended spanner
[4-2]
to screw on
the cutter
[4-3]
.
Release the spindle lock
[4-1]
.
Slide the guide frame
[3-4]
onto the motor unit
[3-5]
until it audibly engages.
7.3 Setting the Mortise Depth
Press one or two snap buttons
[1-8]
.
Set the slide for the routing depth setting
[1-
7]
to the desired routing depth (15 - 70 mm).
Release the snap buttons
[1-8]
.
Check whether the slide
[1-7]
has engaged cor-
rectly.
With the two markers
[1-9]
, you can mark two
routing depths and switch easily between them
using the slide
[1-7]
(e.g. for asymmetric DOMI-
NO dowel depth distribution).
7.4 Setting the Fence Height
The alignment of the clamp levers
[1-12]
and
[1-14]
can be aligned by raising the levers.
When tightened, the levers should not protrude
beyond the contact surface.
a) with selection slide
Loosen the clamp lever for the routing height
adjustment
[5-1]
.
Using the front handle
[5-2]
raise the front part
of the guide frame.
Use the selection switch to set
[5-6]
the desired
routing height
h
(10 mm; 15 mm; 20 mm;
25 mm; 30 mm; 40 mm).
Press the front section of the guide frame down-
wards as far as the stop.
Close the clamp lever
[5-1]
.
b) freely selectable
Loosen the clamp lever for the routing height
adjustment
[5-1]
.
Using the front handle
[5-2]
raise the front sec-
tion of the guide frame.
Pull the selection slide
[5-6]
as far as the stop
in the direction of the motor unit.
Set the desired routing height
h
using the scale
[5-3]
by moving the front section of the guide
frame vertically.
Close the clamp lever
[5-1]
.
CAUTION
Hot and sharp tools
Risk of injury
Wear protective gloves.
WARNING
Risk of injury
Before inserting a new cutter ensure that the
machine, the guide frame and the guides
[3-1]
and
[3-6]
are clean.
Remove any contamination that may be present.
Only use sharp, undamaged and clean tools.
WARNING
Cutter can come out at the rear side of the work-
piece.
Risk of injury
Set the routing depth at least 5 mm less than the
workpiece thickness.
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Festool DF 700 EQ-Plus Domino XL wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info