Bedienungsanleitung Festool DF 700 EQ-Plus Domino XL (Seite 15 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

510172

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

DF 700 EQ

7.5 Setting the Fence Angle



Loosen the clamp lever for the angle adjust-

ment

[5-4]



Set the desired angle:



using the scale

[5-5]

variable from 0° to 90°.



locking at 0°; 22.5°; 45°; 67.5°; 90°.



Close the clamp lever

[5-4]

Set the routing height and depth as low as

possible when mitre routing as otherwise

there is a risk that the cutter will come out

the other side.

7.6 Setting the Mortise Width

Use the adjusting lever

[1-6]

to adjust the width of

the dowel hole you intend to cut for an adequate fit

or set with 3 mm play:

You can see on the display

[1-5]

what dowel hole

width is selected.

7.7 Setting stop pins

Six stop pins

[1-2]

are available on the stop side of

the DOMINO joining machine.

Stop pins that are not required can be individually

engaged by exerting overpressure and released us-

ing the button

[1-13]

These serve as spacers to the cutter centre and can

be inserted at different locations - see image

[6]

7.8 Dust extraction

At the extractor connector

[1-15]

, a Festool mobile

dust extractor with an extraction hose diameter of

27 mm can be connected.

7.9 Widening the contact surface

The contact surface widening device

[7-1]

can be

used to enlarge the contact surface when routing

on the workpiece edge, thus allowing safer guid-

ance of the machine.



Secure the contact surface widening device us-

ing the two screws

[7-2]

on the threaded holes

[7-3]

of the guide frame.

The contact surfaces of the contact surface wid-

ening device

[7-5]

and the table

[7-4]

must be

level.

8 Working with the machine

Wood is a natural, non-homogenous material and

because of this, its dimensions will most likely de-

viate slightly during processing, even if the machine

is set accurately. Machine handling also influence

the degree of working accuracy (e.g. fast-feed

speed). Furthermore, the dimensions of wooden

DOMINOs may vary (for example, due to humidity),

regardless of how they are stored. All of these fac-

tors influence the dimensional accuracy of manu-

factured dowel holes and dowelling joints.



We recommend

routing and joining a test work-

piece before machining the actual workpiece.

Please observe all mentioned safety infor-

mations and the following rules when work-

ing:

– Always secure the workpiece in such a manner

that it cannot move while being processed.

– Always hold the machine with two hands on the

handles

[1-3]

when performing work. This re-

duces the risk of injury and is a prerequisite for

precise work.

– Close the clamp lever for routing height adjust-

ment

[1-14]

and the clamp lever for angle adjust-

ment

[1-12]

to avoid unintentional loosening

during operation.

– Adapt the feed rate to the cutter diameter and

material. Work with a constant feed rate

– Only lay the machine aside when the cutter has

come to a complete standstill.

– Always connect the machine to a dust extractor.

For work that generates dust, wear a dust

mask.

Procedure

Proceed as follows to create a DOMINO dowelling

joint:

Tight fitting dowel 13.5 mm + cutter diameter

Dowel with lateral

play

16.5 mm + cutter diameter

A Three possible spacings to a supply side (1 -

2 - 3)

B Two dowel holes beside each other from a

supply side (1 - 3)

C Two dowel holes by changing the workpiece,

e.g. for cross-section cut.

WARNING

Dust hazard



Dust can be hazardous to health. Always work

with a dust extractor.



Always read applicable national regulations be-

fore extracting hazardous dust.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool DF 700 EQ-Plus Domino XL Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info