Bedienungsanleitung Festool DF 700 EQ-Plus Domino XL (Seite 16 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

510172

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

DF 700 EQ

9 Service and maintenance

The machine is equipped with special carbon

brushes. If they are worn, the power is interrupted

automatically and the machine comes to a stand-

still.

Observe the following instructions:



To ensure constant air circulation, always keep

the cooling air openings in the housing clean

and free of blockages.



Clean the guides

[3-1]

and

[3-6]

of dust depos-

its.



Oil the guides regularly and lightly with resin-

free oil (e.g. sewing machine oil).



We recommend an annual inspection and/or a

check after approx. 100 operating hours at an

authorised customer service workshop. This is

for the safety of the user and the value stability

of the power tool.

10 Troubleshooting

See chapter

1. Select a DOMINO dowel and insert the

suitable bit into the DOMINO joining

machine.

7.2

2. Set the routing depth. 7.3

3. Set the routing height. 7.4

4. Adjust the routing angle if necessary. 7.5

5. Mark the areas on the workpieces that

belong together

[8-1]

so that you will be

able to join them correctly again once

you have cut the dowel holes.

6. APosition the two workpieces to be joined

against one another and mark the

desired positions of the DOMINO dowels

with a pencil

[8-2]

Select the required stop pins. 7.7

7. Set the desired dowel hole width (ade-

quate fit or with 3 mm play).

7.6

8. Cutting the dowel holes

[8]

– The first dowel hole by attaching the

stop pin to the side edge of the work-

piece.

– The following dowel holes according

to the previously made pencil mark-

ings and the scale of the vision panel

[8-3]

Our recommendation:

Please check

each dowel hole for chippings and clear

these if necessary.

Always work with a dust extractor to

improve the removal of chippings.

Route the first hole for each workpiece

without play (dowel hole width = DOM-

INO dowel width) and the other dowel

holes with the large dowel hole width.

WARNING

Risk of injury, electric shock



Always disconnect the mains plug from the

socket before performing maintenance work on

the machine!



All maintenance and repair work which requires

the motor housing to be opened must only be

carried out by an authorised service workshop.

See chapter

Fault Cause Solution

Burns Blunt cutter Use sharp cutter

Dowel hole too narrow. DOMINO

dowel cannot be jointed.

a. Blunt cutter

b. Deposits (e.g. chippings in the

dowel hole)

a. Use sharp cutter

b. Remove deposit and work with

dust extractor

Widening of the dowel hole with

8mm cutter

Routing depth too large (larger

than 50 mm)

Reduce routing depth (max.50 mm)

Splinters at edge of dowel hole Excessive feed rate Reduce feed rate

Dowel hole not parallel to work-

piece edge

Workpiece has shifted during

processing

Secure workpiece properly

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool DF 700 EQ-Plus Domino XL Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info