Bedienungsanleitung Festool DOMINO XL DF 700 EQ (Seite 15 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

498004

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

DF 700 EQ

Connecting and detaching the mains power

cable [1-17] see Fig. [2].

The switch [1-4] is an on/off switch (I = ON,

0 = OFF).

Peel off the protective film from the bot-

tom of the guide frame [3-4].

Remove the transport safety device [1-

18].

7 Settings

7.1 Electronics

The machine features full-wave electronics

with the following features:

Smooth start-up

The electronically controlled smooth start-up

ensures that the machine starts up jolt-free.

Constant speed

The motor speed remains constant through

electronic control to ensure a uniform cutting

speed even when under load.

Temperature cut-out

The machine power supply is limited and the

speed reduced if the motor exceeds a certain

temperature. The machine continues operat-

ing at reduced power to allow the ventilator

to cool the motor quickly. If the machine

temperature exceeds the maximum permit-

ted value for longer periods, the machine

switches off completely after approx. 40 sec-

onds and can only be switched on again once

the motor has cooled sufficiently.

Restart protection

The integral restart protection prevents the

machine from automatically starting up

again after an interruption in power when the

machine is used in continuous operating

mode. In this case the machine must be

switched off and then switched back on

again.

7.2 Changing tools

Removing the tool

Lift the unlocking device [3-2] until it au-

dibly disengages using the open-ended

spanner [3-3] supplied (SW 12).

Separate the motor unit [3-5] from the

guide frame [3-4].

Press and hold the spindle lock [4-1].

Loosen the cutter [4-3] using the open-

ended spanner [4-2] and remove.

Release the spindle lock [4-1].

Inserting the tool

Press and hold the spindle lock [4-1].

Use the open-ended spanner [4-2] to

screw on the cutter [4-3].

Release the spindle lock [4-1].

Slide the guide frame [3-4] onto the mo-

tor unit [3-5] until it audibly engages.

7.3 Setting the Mortise Depth

Press one or two snap buttons [1-8].

Set the slide for the routing depth setting

[1-7]to the desired routing depth (15 - 70

mm).

WARNING

Risk of injury, electric shock

Always pull the plug out of the socket be-

fore performing any type of work on the

machine!

CAUTION

Hot and sharp tools

Risk of injury

Wear protective gloves!

WARNING

Risk of injury

Before inserting a new cutter ensure that

the machine, the guide frame and the

guides [3-1] and [3-6] are clean.

Remove any contamination that may be

present.

Only use sharp, undamaged and clean

tools.

WARNING

Cutter can come out at the rear side of

the workpiece.

Risk of injury

Set the routing depth at least 5 mm less

than the workpiece thickness.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool DOMINO XL DF 700 EQ Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info