Bedienungsanleitung Festool DOMINO XL DF 700 EQ (Seite 16 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

498004

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

DF 700 EQ

Release the snap buttons [1-8].

Check whether the slide [1-7] has en-

gaged correctly.

With the two markers [1-9], you can mark

two routing depths and switch easily be-

tween them using the slide [1-7](e.g. for

asymmetric DOMINO dowel depth distri-

bution).

7.4 Setting the Fence Height

The alignment of the clamp levers [1-12]

and [1-14] can be aligned by raising the

levers. When tightened, the levers should

not protrude beyond the contact surface.

a) with selection slide

Loosen the clamp lever for the routing

height adjustment [5-1].

Using the front handle [5-2] raise the

front part of the guide frame.

Use the selection switch to set [5-6]the

desired routing height

(10 mm;

15 mm; 20 mm; 25 mm; 30 mm;

40 mm).

Press the front section of the guide frame

downwards as far as the stop.

Close the clamp lever [5-1].

b) freely selectable

Loosen the clamp lever for the routing

height adjustment [5-1].

Using the front handle [5-2] raise the

front section of the guide frame.

Pull the selection slide [5-6] as far as the

stop in the direction of the motor unit.

Set the desired routing height

using the

scale [5-3] by moving the front section of

the guide frame vertically.

Close the clamp lever[5-1].

7.5 Setting the Fence Angle

Loosen the clamp lever for the angle ad-

justment [5-4].

Set the desired angle:

using the scale [5-5] variable from 0°

to 90°.

locking at 0°; 22.5°; 45°; 67.5°; 90°.

Close the clamp lever [5-4].

Set the routing height and depth as

low as possible when mitre routing as

otherwise there is a risk that the cutter

will come out the other side.

7.6 Setting the Mortise Width

Use the adjusting lever [1-6] to adjust the

width of the dowel hole you intend to cut for

an adequate fit or set with 3 mm play:

You can see on the display [1-5]what dowel

hole width is selected.

7.7 Setting stop pins

Six stop pins [1-2] are available on the stop

side of the DOMINO joining machine.

Stop pins that are not required can be indi-

vidually engaged by exerting overpressure

and released using the button [1-13].

These serve as spacers to the cutter centre

and can be inserted at different locations -

see image [6]:

7.8 Dust extraction

At the extractor connector [1-15], a Festool

mobile dust extractor with an extraction hose

diameter of 27 mm can be connected.

7.9 Widening the contact surface

The contact surface widening device [7-1]

can be used to enlarge the contact surface

when routing on the workpiece edge, thus al-

lowing safer guidance of the machine.

Secure the contact surface widening de-

vice using the two screws [7-2] on the

threaded holes [7-3]of the guide frame.

The contact surfaces of the contact sur-

face widening device [7-5] and the table

[7-4] must be level.

Tight fitting dowel 13.5 mm + cutter diame-

ter

Dowel with lat-

eral play

16.5 mm + cutter diame-

ter

A Three possible spacings to a supply

side (1 - 2 - 3)

B Two dowel holes beside each other

from a supply side (1 - 3)

C Two dowel holes by changing the work-

piece, e.g. for cross-section cut.

WARNING

Dust hazard

Dust can be hazardous to health. Always

work with a dust extractor.

Always read applicable national regula-

tions before extracting hazardous dust.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool DOMINO XL DF 700 EQ Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info