Bedienungsanleitung Festool DOMINO XL DF 700 EQ (Seite 17 von 116) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

498004

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

DF 700 EQ

8 Working with the machine

Wood is a natural, non-homogenous material

and because of this, its dimensions will most

likely deviate slightly during processing,

even if the machine is set accurately. Ma-

chine handling also influence the degree of

working accuracy (e.g. fast-feed speed).

Furthermore, the dimensions of wooden

DOMINOs may vary (for example, due to hu-

midity), regardless of how they are stored.

All of these factors influence the dimensional

accuracy of manufactured dowel holes and

dowelling joints.

We recommend

routing and joining a

test workpiece before machining the actu-

al workpiece.

Please observe all mentioned safety in-

formations and the following rules

when working:

– Always secure the workpiece in such a

manner that it cannot move while being

processed.

– Always hold the machine with two hands

on the handles [1-3] when performing

work. This reduces the risk of injury and is

a prerequisite for precise work.

– Close the clamp lever for routing height

adjustment [1-14]and the clamp lever for

angle adjustment [1-12]to avoid uninten-

tional loosening during operation.

– Adapt the feed rate to the cutter diameter

and material. Work with a constant feed

rate

– Only lay the machine aside when the cutter

has come to a complete standstill.

– Always connect the machine to a dust ex-

tractor.

For work that generates dust, wear a

dust mask.

Procedure

Proceed as follows to create a DOMINO dow-

elling joint:

9 Service and maintenance

The machine is equipped with special carbon

brushes. If they are worn, the power is inter-

rupted automatically and the machine comes

to a standstill.

See chapter

1. Select a DOMINO dowel and insert

the suitable bit into the DOMINO

joining machine.

7.2

2. Set the routing depth. 7.3

3. Set the routing height. 7.4

4. Adjust the routing angle if neces-

sary.

7.5

5. Mark the areas on the workpieces

that belong together [8-1]so that

you will be able to join them cor-

rectly again once you have cut the

dowel holes.

Position the two workpieces to be

joined against one another and

mark the desired positions of the

DOMINO dowels with a pencil [8-

2].

Select the required stop pins. 7.7

7. Set the desired dowel hole width

(adequate fit or with 3 mm play).

7.6

8. Cutting the dowel holes [8]:

– The first dowel hole by attaching

the stop pin to the side edge of

the workpiece.

– The following dowel holes ac-

cording to the previously made

pencil markings and the scale of

the vision panel [8-3].

Our recommendation:

Please

check each dowel hole for chip-

pings and clear these if necessary.

Always work with a dust extractor

to improve the removal of chip-

pings.

Route the first hole for each work-

piece without play (dowel hole

width = DOMINO dowel width) and

the other dowel holes with the

large dowel hole width.

WARNING

Risk of injury, electric shock

Always disconnect the mains plug from the

socket before performing maintenance

work on the machine!

All maintenance and repair work which re-

quires the motor housing to be opened

must only be carried out by an authorised

service workshop.

See chapter

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool DOMINO XL DF 700 EQ Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info