Bedienungsanleitung Festool DSC-AG 125 (Seite 19 von 126) (Alle Sprachen)

778812

Zoom out

Zoom in

Vorherige Seite

1/126

Nächste Seite

resist kickback forces. Always use auxiliary

handle, if provided, for maximum control over

kickback or torque reaction during start-up.

The operator can control torque reactions or

kickback forces, if proper precautions are taken.

b) Never place your hand near the rotating ac-

cessory. Accessory may kickback over your

hand.

c) Do not position your body in the area where

power tool will move if kickback occurs. Kick-

back will propel the tool in direction opposite to

the wheel’s movement at the point of snagging.

d) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing

have a tendency to snag the rotating accessory

and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving blade

or toothed saw blade. Such blades create fre-

quent kickback and loss of control.

Additional safety instructions for grinding and

cutting

Safety Warnings Speciﬁ c for Grinding and

ABRASIV Cutting-Off Operations:

a) Use only wheel types that are recommended

for your power tool and the speciﬁ c guard

designed for the selected wheel. Wheels for

which the power tool was not designed cannot

be adequately guarded and are unsafe.

b) The guard must be securely attached to the

power tool and positioned for maximum safe-

ty, so the least amount of wheel is exposed

towards the operator. The guard helps to pro-

tect operator from broken wheel fragments

and accidental contact with wheel.

c) Wheels must be used only for recommended

applications. For example: do not grind with

the side of cut-off wheel. ABRASIV cut-off

wheels are intended for peripheral grinding,

side forces applied to these wheels may cause

them to shatter.

d) Always use undamaged wheel ﬂ anges that

are of correct size and shape for your selected

wheel. Proper wheel ﬂ anges support the wheel

thus reducing the possibility of wheel break-

age. Flanges for cut-off wheels may be differ-

ent from grinding wheel ﬂ anges.

e) Do not use worn down wheels from larger

power tools. Wheel intended for larger power

tool is not suitable for the higher speed of a

smaller tool and may burst.

Additional safety instructions for abrasive cut-

ting

Other special safety instructions for abrasive

cutting:

a) Prevent the cutting disc from seizing and do

not apply excessive pressure. Never make ex-

cessively deep cuts. Overloading the cutting

disc increases the stress placed on the disc,

susceptibility to tilting or seizing and the pos-

sibility of kickback or disc breakage.

b) Avoid the area in front of and behind the rotat-

ing cutting disc. If you move the cutting disc in

the workpiece away from the body, the electric

power tool may kick back, throwing the rotating

disc directly towards you.

c) If the cutting disc seizes or you intend to take

a break from work, switch off the machine and

hold still until the disc comes to a complete

stop. Never attempt to remove the rotating

cutting disc from the cut, otherwise the ma-

chine may kick back. Identify and rectify the

cause of the seizure.

d) Do not switch the electric power tool on again

while the disc is still embedded in the work-

piece. Allow the cutting disc to reach full

speed before carefully continuing with the

cut. Otherwise the disc may seize, jump out of

the workpiece or cause a kickback.

e) Always support panels or large workpieces to

minimise the risk of a kickback caused by a

seized cutting disc. Large workpieces may sag

under their own weight. The workpiece must

be supported either side of the disc, both near

the cut and along the edge.

f) Proceed with particular caution when mak-

ing „pocket cuts“ in existing walls or other

invisible areas. A cutting disc plunged into a

wall may cut into gas or water pipes, electric

cables or other objects and cause the machine

to kick back.

Additional safety instructions for wire brushing

operations

Safety Warnings Speciﬁ c for Wire Brushing

Operations:

a) Be aware that wire bristles are thrown by the

brush even during ordinary operation. Do not

overstress the wires by applying excessive

load to the brush. The wire bristles can easily

penetrate light clothing and/or skin.

b) If the use of a guard is recommended for wire

brushing, do not allow any interference of the

wire wheel or brush with the guard. Wire wheel

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool DSC-AG 125 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info