Bedienungsanleitung Festool DSC-AG 125 (Seite 21 von 126) (Alle Sprachen)

778812

Zoom out

Zoom in

Vorherige Seite

1/126

Nächste Seite

Increase possible for other applications, with oth-

er insertion tools or if not maintained adequately.

Take note of idling and downtimes of machine!

7 Safety elements assembly

WARNING

Risk of accident, electric shock

Always pull the plug out of the socket before

performing any type of work on the machine.

CAUTION

Always use the additional handle to guarantee

a safe, non-tiring working posture.

7.1 Additional holder

Special construction “VIBRASTOP” regulates the

vibrations with additional holder [1-14]. Addition-

al holder can be screwed from the left or right

side of gearbox.

7.2 Exhaust cover

Assembly

Before inserting the machine into the cover,

we recommend you to turn the machine case

by 180° with respect to the gearbox so that the

switch is on the right hand side.

Arrest the exhaust cover in the top position and

put in on the side, with the clamping sleeve

up. Then put the clamping neck [3-1] of the

grinder into the sleeve. Put the guiding tabs

[3-2] into the grooves on the clamping neck of

the grinder – detail [3].

Turn the grinder counter-clockwise to the suit-

able working position – cf. Fig. [4], set the cover

to the maximum cut-through and arrest in this

position.

Tighten sleeve with screw – Fig. [4 a]. When

tightening, be careful about the correct right-

angle setting of the grinder’s bearing cover in

the exhaust cover’s sleeve.

Removal

The cutting disc must be dismounted before

the disassembly of the exhaust cover.

Set the cover to a cut depth of 10 mm and put

it down with the grinder at the bottom.

Loosen screw of sleeve.

Set the cover to the top position.

Turn the guiding tab [5-1] into the groove on

the grinder’s clamping neck. The turning can

be checked – the corresponding mark is on the

side of the disc – Fig. [5].

Remove the cover from the grinder’s clamping

neck.

7.3 Dust extraction

WARNING

Dust hazard

Always work with a dust extractor.

To ensure suction, put the hose of a Festool

vacuum cleaner class L, M or H into the suction

adapter [1-12].

Warning: Always work with the suction connect-

ed. Use exclusively antistatic vacuum cleaners to

prevent discharges of static electricity in dusty

environments.

8 Diamond cutting disc

8.1 Clamping

WARNING

Do not use quick-change nuts for clamping the

disc!

WARNING

Only use diamond cutting discs recommended

by the manufacturer and the prescribed ﬂ ang-

es included with the cover and the grinder.

-For reasons of safety, always use original Fes-

tool grinding discs!

-Sintered cutting discs must not be used!

-If the permissible revolution speed is given on

the disc, it must not be lower than the highest

no-load speed of the grinder.

-Discs with a permissible peripheral speed of 80

m/s and higher may be used.

-Test new cutting discs by letting them run for

about one minute with no load.

-Unbalanced or vibrating discs should not be

used and should be discarded.

-Protect grinding discs from shock, impact and

lubricants.

-If the grinding and cutting wheels are worn

down to the mark on the wheel guard (see the

arrow sign), they should be replaced with new

ones. This maintains the optimum grinding and

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool DSC-AG 125 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info