Bedienungsanleitung Festool DSC-AG 125 (Seite 22 von 126) (Alle Sprachen)

778812

Zoom out

Zoom in

Vorherige Seite

1/126

Nächste Seite

cutting performance of the machine (periph-

eral speed of the grinding and cutting wheels).

Set the sliding stop for cut depth [2-5] on scale

[2-4] to a depth value of 10 mm.

Push the arresting button [1-1] and push the

cover in.

Release the arresting button [1-1] and let the

cover be arrested when it gets to the set depth.

Unlock with button [2-1] and fully open the disc

cover.

Clean the ﬂ ange [6-4] and clamping nut [6-2],

as well as the clamping faces of the cutting

disc [6-3].

Put the ﬂ ange [6-4] on the grinder’s spindle

with the shoulder facing outward.

Put on the disc [6-3]; take care to comply with

the prescribed direction of rotation (arrow on

the disc vs. arrow on the machine). The ﬂ ange

shoulder must exactly ﬁ t in the disc’s opening.

Screw on the clamping nut [6-2] with the shoul-

der facing outward (from the disc), press on the

spindle arrest and tighten with wrench [6-1].

Close the disc cover.

Before switching on, check free rotational

movement of the disc.

8.2 Guide system [ﬁ gure 7]

WARNING

Only use discs of thickness up to 3 mm!

Use the guide bar [7-1] for accurate cuts.

The side clearance of the disc guiding can be set

with the aid of the adjusting screws [1-9].

Guide bars

On the bottom face of the guide bar there are anti-

skid strips, which ensure safe contact and prevent

the workpiece from scratching.

The bar can also be secured with the aid of special

clamps FSZ 300 [7-2], pushed into the special

guide grooves. Safe guiding on uneven surfaces

is thus enabled.

WARNING

The guide bars are equipped with burr protec-

tor, which must be cut off before the ﬁ rst use.

Connector

Depending on the particular application and the

workpiece size, several guide bars can be con-

nected with the aid of a connector spring [7-3].

Fast connection of guide bars can be secured by

screws in the threaded openings.

9 Activation

WARNING

Risk of accident if the machine is operated us-

ing unauthorised voltages or frequencies.

The mains voltage and the frequency of the

power source must correspond with the spec-

iﬁ cations on the machine’s name plate.

In North America, only Festool machines with

the voltage speciﬁ cations 120 V/60 Hz may

be used.

Set the sliding stop for cut depth [2-5] on scale

[2-4] (top edge of the stop) to the requested depth

of the cut – loosen and tighten the stop screw [2-

6] as necessary.

The cut depth scale is valid for cutting without a

bar.

The scale is for orientation only. The actual depth

of the cut may be affected by, for example, manu-

facturing tolerances or the wear of the diamond

disc’s segment. If en exact depth is required, it

is necessary to measure the actual depth on a

test cut.

9.1 Switching on – off

Switching on

Slide the on/off switch [1-5] forwards.

Continuous operation: pressing the front part

of the switch at the same time locks the on/

off switch.

The electric power tool starts.

Only make contact with the material once the

machine has reached operating speed.

Switching off

Lift the electric power tool from the processed

material.

Release the on/off switch [1-5].

During continuous operation: press on the

rear part of the on/off switch [1-5].

WARNING

Risk of injury

Rebound, ejected parts

Before setting down the machine, wait until

the rotating tool has come to a complete stop.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Festool DSC-AG 125 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info